Resistor spark plugs - resistor spark plug caps.

Does using a resistor spark plug, with a resistor spark plug cap effect the spark?

Advanced Ultralight Aircraft News Web Magazine
PO Box 1710 Holland Landing Ontario Canada L9N 1P2 905-836-7588

Click here to submit an ultralight aircraft classified ad!


   Search this site 
 powered by FreeFind

Call UltralightNews 
from your computer by clicking below!

Let me know what you think about the site - sign my guest book!
Click here!


Click here subscribe to the Ultralight Flyer Video Magazine!
ONLY $15 per year! 
For hours of web video on ultralight aircraft!





This space is for rent. Click here for more information!

You can help support Ultralight News by visiting our sponsor at the bottom of this article.  

Each visit earns us 12 cents, which helps keep Ultralight News on the web, and brings you Ultralight News EXTRA each month Thanks D.L.

Click here for this month's specials!

From: Rainier Lamers <>

Subject: Was: Spark plug safety tip

Date: Fri, 26 Feb 1999 16:35:56 +0200

Recently an interesting thread on this newsgroup discussed the relative merits of resistive plugs as used on many Rotax engines.

In order to get to the bottom of this Spark plug vs. resistance story I decided to do some experiments. I am a electronics engineer (when I am not flying :-), so I have the tools for the job.

First a coil was rigged for the job to create the high voltage required for the plugs. I used a standard car coil combined with an electronic interrupter/generator. Spark plugs with and without resistors as well as caps with and without resistors where obtained. The plugs where all equally gapped to 0.4mm. I used a scope to monitor the voltage at the plug tip as well as at the coil (via high impedance probe - scopes are expensive !). The result was quite interesting.

As expected, the voltage at the cable (before any resistor) rises at the same rate regardless of resistance until the point of firing. Thereafter however the picture changes.

The coil generates a certain amount of energy. This energy wants to go somewhere. At a voltage of about 7KV the plug fires (irrespective of resistance). Until that happens NO CURRENT FLOWS. Whether you have resistance or not does not matter. A paltry 5KOhms does not do anything when compared to the nearly infinite resistance of the gap itself (until the plug fires that is).

Once the plug fires the resistance comes into being. The coil cannot get rid of its energy in the shortest possible time due to the resistance.

This reduces current flow in the spark and it takes quite a bit longer until the energy in the coil has expelled itself via resistor and spark gap. This results in a longer spark. However the spark is weaker due to energy loss in the resistor.

The scope shows this very nicely and it also gives reason why the resistor helps to suppress RF. With the resistor changes in the rate of current flow are much less resulting in "flatter" edges on the voltage vs. time curve that the scope shows you. This implies less high frequency components of the signal in the cable feeding the spark plugs.

Conclusion: It is quite safe to insert a resistor. It will not stop the plug from firing at all. High values will however lead to a weaker spark -but it is going to spark, no matter what. 

However, contaminate the plug with fuel (even just a little) and a high value resistor will cause the plug not to fire. 10K plugs as are used on some motorcycles now are about maximum I would guess. 

I do not recommend you use resistance plugs or caps at all on inverted Rotax installations due to the possibility of plug contamination by oil and fuel.

As further experiment I increased the resistance value to see what effect this is going to have. I tried values 10K, 47K, 100K, 220K, 470K, 820K and 1M.

Even with 1M the plug (dry, not contaminated) still fired but noticeably weaker and longer (you can actually see it firing longer !). But contaminate this plug even slightly (a little moisture by exhaling onto it) and you get no spark.

Finally, a disclaimer: All of the above has been found out by a little experimenting. Use the results at your own peril. Don't get back to be with a heap of bent metal that used to be your plane claiming it is because I said you should put 1M resistors into your spark plug leads. I did NOT.

Rainier Lamers.

A monthly newsletter packed full of information on ultralight aviation!

Advanced Ultralight Aircraft News Web Magazine PO Box 1710 Holland Landing Ontario Canada 
L9N 1P2 905-836-7588.
No part of this publication may be copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language, in any form or by any means, electronic,  mechanical, manual, or otherwise,  without the written permission of Dave Loveman. Copyright Ultralight News -  Ultralight Flyer.