Name:

Address:

 

 

Email:

Tel:

Fax:

 


Cello Case Price List

All prices + 17.5% VAT for UK and EC customers.
VAT is not chargeable on cases that are exported outside the EC.

"GBP" = UK Pounds Sterling
Original Model Cases Please tick box  
Standard fibreglass 18-20lb (8.2-9.1kg)   GBP 845
Carbon composite approx. 12.2lb (5.5kg)   GBP 1383
Carbon composite approx. 10.4lb (4.7kg)   GBP 1383
Smaller Classically Shaped Model Cases    
Fibreglass 12-17lb (5.4-7.7kg)   GBP 845
Carbon composite approx. 9.2lb (4.2kg)   GBP 1383
Carbon/kevlar approx. 7.2lb (3.3kg)   GBP 1383
Extras    
Wheels stainless steel mount (480g)   GBP 41
Wheels carbon mount 14oz (400g) [classical cases]   GBP 41
Top Edge and Corner Buffers   GBP 24
Carrying Strap Fixings only   GBP 3
Carrying Strap   GBP 25
End-pin Well   GBP 25
Colour choice other than white   GBP 24
Padlock Fixings only   GBP 2
Padlock   GBP 4
Slimline Soft Outer Cover (2cm/0.75in)   GBP 238
'Blobby' Soft Outer Cover (5cm/2in)   GBP 270
Felt Cape   GBP 13
Crushed Velvet Lining   GBP 95
Tortellier End Pin Pouch   GBP 12
Simple Backpack   GBP 28
Fiedler Backpack   GBP 110
Transport   Phone/Email

Cases can now be made in a wide range of colours.
Cases weights do not include wheels which add approx. 1.2lbs (500g) or 14oz (400g) depending on the mount.
Case weights vary due to the hand-crafted nature of the product.
Transport additional as quoted.

 

Table of 'cello measurements.

  Your sizes Average sizes
Approximate width horizontally from A peg to C peg ends   16cm
Back length excluding half round where neck joins   75.5cm
Upper bouts (shoulders)   34cm
Lower bouts (hips)   44cm
Bridge height   9cm
Rib depth at shoulders including edges of front and back   12.5cm
Rib depth at hips including edges of front and back   12.8cm
Distance beneath fingerboard to surface of belly at neck join   2.2cm
Bridge to back total depth   26.7cm
Overall height excluding end pin   121cm
End pin unit and spike   5.5
Does the spike screw point forward or to the side?    

Chart

Cello Case Chart



 

Illustration of alternative method of measuring the bridge to back size.

Measuring the front to back Measuring the depth of the 'cello from bridge to back is very awkward and is easiest if the 'cello is laid on a table and held steady. One person holds a ruler across the bridge and measures from one end of it down to the table. Another person measures from the other end of the ruler down to the table. When the two measurements are the same that is the correct figure. Alternatively place the 'cello on its side with the bridge against a wall and place a large book up to the back of the instrument. Remove the 'cello and measure the gap.

When completing the fitting diagram please take the measurements carefully and after filling in the diagram please check they are correct by remeasuring. We can only visualise your 'cello based on the measurements we are given. If the instrument is either very large or rather small then an outline drawn on newspaper of the whole instrument, which we mount on card, is useful to us. When measuring the back length do not include the half-round where the neck joins the back and when measuring the overall length of the 'cello do not include the end pin unit which is measured separately


 

Bass Case prices:

All prices + 17.5% VAT for UK and EC customers.
VAT is not chargeable on cases that are exported outside the EC.

"GBP" = UK Pounds Sterling

Fibreglass without gelcoat finish: 28kg/62lb   GBP 1639
Fibreglass with gelcoat finish: 31.5kg/69lb   GBP 1719
Fibreglass + extra layer, hardwood base runners: 36kg/79lb   GBP 1799
Carbon composite: 20-24kg/44-53lb   GBP 3055
Customisation options:    
Colours other than white or light grey   GBP 26
Hardwood base runners   GBP 20
Wooden runners on the back of the case (orchestras)   GBP 15

Back to Stevensoncases