Tire/fender clearance is determined by frame design. Well designed frames generally have room for tires of reasonable width to be installed, and ideally there should also be room for fenders to be installed without risk of the tire rubbing on the fender.
The areas of concern are where the front tire fits through under the fork crown, and where the rear tire fits between the seatstays and chainstays. There's also often an issue with the vertical clerance between the tire tread and the underside of the fork crown or the seatstay bridge, or clearance between the tire and the brake caliper.
Historically, track bikes have been made with minimal clearance, since nobody needs anything but skinny tires on the track. Starting in the 1980s, road bikes began to copy this design, and these days most "racing" type bikes have stupidly tight clearance. This is basically a styling fad, and seems to be beginning to run its course. While it was in full swing, it created a vicious cycle: Bikes with super-tight clearance need brake calipers with very short arms. As the tight cleranace fad progressed, brake manufacturers shifted most of their production to super-short reach calipers, and calipers with longer reach became unavailable. This forced frame makers to continue making frames/forks with excessively tight clearance, which in turn led to the demise of medium reach brakes...
Largely thanks to the efforts of Rivendell's Grant Petersen, calipers with longer arms are once again becoming available, and many bike manufacturers are once again making bikes that combine speed with versatility.
If your frame has tight clearance, there's no easy fix. The only way around the problem is to go to a smaller diameter wheel.
This site has an article on conversions like this.
If you pedal through corners, there is a chance of striking one of your pedals on the roadway as you lean into the turn. The risk of this depends on several factors, including:
Pedal cornering clearance is a particularly importan issue on a fixed gear bike, because the fixed gear forces you to pedal all the time. In addition, if you strike a pedal on a fixed gear bike, it will tend to lift the rear wheel up off the road, and you will spin out and crash.
Bottom Bracket Drop Calculation Spreadsheet
The other major area where clerance is an issue is when the rider's toe or toe clip can strike the back edge of the front tire or front fender.
Up until the late '70's, cleats were leather or aluminum, and were nailed onto the bottom of the shoe with many tiny nails. The usual procedure was to have the cyclist ride for a while without the cleats, until the pedal would make a mark on the sole of the shoe. This mark would then be used as a guide to locate where the cleat should be nailed on.
In the '70's, adjustable plastic cleats were introduced, and immediately rendered the nail-on system obsolete...unfortunately, they also precipitated a rash of knee injuries, because riders would adjust them by pure guesswork, and this often caused un-natural stresses on their knees. The invention of the Fit-Kit R.A.D. made it possible to adjust this type of cleat even more accurately than the old sole-impression system.
Modern clipless pedals have solved these problems, and, in my opinion, nobody should still be using classic cleats. Now that there is an alternative, they are just not worth the risk.
A clincher tire has a separate inner tube, which is basically a rubber balloon. This fits inside the tire, and the tire is mounted on the rim by lifting the beads over the edge of the rim. The middle of the rim makes a sort of valley, and while the tire is being installed, most of the bead can fit into this valley. This gives enought slack to allow the bead to be pushed or pulled over the edge of the rim, even though outside diameter of the rim is larger than the inside diameter of the bead.
Strictly speaking, the term "clincher" is slightly incorrect, as it applied to an obsolete style of tire which had ribs in the edges of the tire which fitted into grooves on the rim, where the tire was folded under the tube. The air pressure in the tube pressed the rib into the groove, and "clinched" the tire in place. People who are fussy about this prefer the term "wire-on."
Other types of tires include airless tires, single-tubes (both obsolete) and tubulars.
"Clipless" or "Step-in" pedals use a mechanism similar to a ski binding. In fact the first successful system was made by a ski binding manufacturer, Look. Clipless pedals use a cleat which is bolted to the bottom of the shoe. When the rider steps on the pedal with the cleat, the cleat locks into the pedals mechanism, and is held firmly in place. Some systems hold the foot at a fixed angle, others allow various amounts of "float", or angular rotation of the foot on the pedal.
With most clipless pedal systems, the foot is disengaged by twisting the heel outward. Some of the earlier systems, such as the pioneering Cinelli model, required the rider to reach down and operate a release mechanism by hand. This style is sometimes jocularly referred to as "death cleats."
A club bicycle will typically have Reynolds 531 frame tubing, a narrow, unsprung leather saddle, reversed North Road handlebars (or drop bars), steel "rat trap" pedals with toe clips and 597 mm (26 x 1 1/4) or 630 mm (27 x 1 1/4) wheels. Even fairly high-end models will use steel rims, which, at the time, were widely believed to be superior to aluminum. The steel Dunlop Special Lightweight rims used on the better club bicycles could give the aluminum rims of the day a run for their money.
Club biycles would be likely to have a more exotic Sturmey-Archer hub, perhaps a medium- or close-ratio model, 3 or 4 speed. A very few even were equipped with the rare ASC 3-speed fixed-gear hub.
Many club bicycles were single-speed machines, usually with a reversible hub: single-speed freewheel on one side, fixed-gear on the other. Starting in the late '50's, derailers began to be used on this type of bicycle as well.
Although primarily intended for fast group rides with clubmates, club bicycles were also commonly used for serious touring, and also for time-trialing.
See also my Article on English 3-speeds.
Threaded Freewheel | Threaded Hub | Cassette Hub | Cassette Cluster |
---|
See also seat cluster.
Accessories | Bicycles | Parts | Specials | Tools |
---|
If you would like to make a link or bookmark to this glossary, the URL is:
http://sheldonbrown.com/glossary
If you would like to make a link or bookmark to a specific definition, that's fine too. I am committed to keeping the urls stable, so I won't be breaking your link.