6mmBR Cartridge Guide
Accurate, Efficient, Easy to Tune, and Capable from 100 to 1000 yards
6mmBR, 6BR, 6mm BR Norma, Accurate Benchrest Rifle Cartridge, 6PPC reloading, shooting, hunting rifles. 243 .243 caliber
6mmBR.com SPONSORS

6BR 6mmBR 6mm BR Norma 6BR Remington blueprint diagram
6mmBR -- Our Favorite Cartridge
Long popular in Europe, in the past few years the 6mmBR (6BR) cartridge has become much more widely adopted by North American shooters. It's easy to understand why. The 6BR is superbly accurate, very efficient, and very versatile. A 6BR can set world records at 600 yards (and even 1000), yet it is easy to tune, and it is just as well suited for a long day in the varmint fields.

6BR shooters know this chambering offers great factory brass (Lapua and Norma), and a fantastic selection of short- and long-range match bullets. The 6PPC may be a little more accurate at 100/200 yards. But at 300 to 600 yards, the 6BR's extra capacity gives it an edge, making it a very tough cartridge to beat. The 6BR remains the dominant cartridge in 300m competition and, thanks to shooters like Terry Brady, the 6BR holds many of the 600-yard BR records.

Here then, we have a cartridge that delights both varminters and match shooters--benchresters and position shooters alike. The 6BR offers easy load development, excellent barrel life (expect 2500 rounds or more of top accuracy), and low component costs. Despite its small size, the 6BR offers better ballistics than a .308 Win, though the 6BR burns 33% less powder and produces 55% less recoil. (6BR with 105gr compared to .308 with 175gr.)

6mmBR Cartridge Basics
The 6mm BR that is most commonly used today is also called 6mm Norma BR, "6BR Norma", or just plain "6BR". This cartridge was based on the original 6mm Remington Benchrest case. Though there are very slight differences between the SAMMI spec for the 6mm Rem BR and the CIP spec for the 6mm BR Norma, the OAL case length is the same. We've observed that there may be small variances in base dimensions among production brass, from brand to brand. Though Norma standardized the round, most people shoot Lapua brass, because of its superior quality and uniformity, not to mention lower cost. The case capacity of Lapua brass is about 38-39.5 grains of H20, after fire-forming. The exact capacity depends on your gun's chamber and the brass lot. The 6mm BR is one of the most accurate cartridges in existence, bettered only by the PPC type cases in group shooting, and the 30BR in score shooting. The 6BR is very versatile, capable of great accuracy with bullets ranging from 50 to 108 grains.

Berger Bullets J4 Jackets

QUICK Navigation
6BR FAQ6BR Match Loads6BR Varmint LoadsFactory Loaded AmmoSierra Load Guide

6BR Reloading--Powders, Bullets, and Favorite Recipes

6mmBR 6BR Reloading GuideVarmint Loads | Sierra Load-Map | Bullet Comparator
Component Vendors | Factory-loaded Ammunition
Reload load data 6mm powder bullets Hodgdon Vihtavuori Lapua
We could fill a book with 6mm BR reloading recipes, case prep secrets, accurizing tips, and miscellaneous voodoo. Or we could tell you simply take a new Lapua 6BR case, add a CCI 450 primer, drop in 30 grains of Varget, top it with a Fowler 80gr FB bullet at the lands, and shoot it.

Chances are that can give you a .30" group at 100yds in a good gun. But for those of you who won't settle for the simple answer, here's a summary of things that work...

6mmBR.com SPONSORS

Preferred Powders
For the 70-90 grain bullets, Vihtavuori N-135 and H4895 are excellent choices. For the 105-108 grain projectiles, A good starting point is Varget sparked by CCI 450 primers. That's a combo proven in competition. Varget is accurate, works with all bullet weights and is relatively insensitive to temperature shift. Our recent Rail-Gun Tests, however, have shown Reloader 15 to be equally accurate, and able to deliver up to 50 fps more velocity with the heavier bullets. H4895 also proved very accurate with the heavier bullets in the 2880 fps range. Other good choices for the heavy bullets include VV N-140, N-150, N540, and Norma 203-B. Reloader 15 has produced great velocities with low ES, giving more speed than Varget at similar pressures. Norma uses 203-B in its Diamond Line 6BR ammo.

Powder Burn Rates | Recommended Powder & Primer Vendor: Powder Valley, (800) 227-4299.

Best Bullets
For short range: 80gr Berger or Fowler FB, 74gr Berger FB, or any of the good 68gr custom bullets. We've had many reports (confirmed by our own testing), that the Berger 80-grainers shoot superbly in both slow- and fast-twist barrels, from 12-twist to 8-twist. If you want to see how tight that 1:8" barrel of yours can shoot, load up some Berger 80s 0.015" into the lands with a stout load of N-135.

For medium range or 1:10 twist barrels: Berger 88gr Low Drag FB, BIB 95gr FB, or Hornady 87-gr V-Max. The BIB is superbly accurate, having shot sub .2" groups at 200 yards.

For long range: Berger 105gr VLD or the new 108gr Match, 100gr or 106gr Clinch River VLD, 105gr JLK (Swampworks), 105gr Lapua Scenar, 107gr Sierra MK, or 103gr Spencer. The value choice is Hornady's 105gr A-Max ($16/100 at MidSouth Shooters Supply, #003-24562).

The Lapua 105gr Scenar is a very uniform bullet and ultra-accurate, but the max diameter is 0.24285, compared to 0.2433+ for some other brands. Accordingly the Scenars may prefer a tighter bore. They shot superbly in this editor's PacNor 8-twist and a .236-land Krieger tested by Jackie Schmidt.

Primer Selection
CCI BR4s and 450s are giving the best velocities, with lowest ES, for the 100+gr bullets. For the shorter bullets, the Fed 205s work well. Federal 205s give good accuracy, but they don't handle high pressures as well as the CCIs, which have a harder cup. Stick to CCIs for hot loads.

Case Prep
With brand new Lapua brass, we recommend you run an expander mandrel down the neck for starters. This will iron out any dents or folds and will reduce neck tension a bit. Neck tension on the virgin brass is more than you need, and by lessening it somewhat you'll find your bullets seat more consistently. Always chamfer the mouth before seating. We use a standard Forster 45-degree tool, then smooth the chamfer with a bit of green nylon scouring pad. Be sure to remove all burrs--don't leave any sharp edges on the chamfer. You may also want to try the K&M 4-degree tapered chamferer, but don't cut too deep--a slight chamfer is all you need. About flash holes--we suggest leaving them alone when using Lapua brass. Our tests suggest that ES and SD may increase with ANY modification of the Lapua Flash-holes, which run 1.50mm (.059") out of the box.

flash hole deburring toolHowever, recent lots of Lapua 6BR brass have shown a few cases per box where there is a little flake of brass on the edge of the flash hole. You'll want to pop this out. A Pin Vise with #53 or 19/32 bit works well for the job. If you do decide to actually ream the flash hole, use a K&M or Sinclair deburring tool for small primer holes--but be gentle, don't ream the hole out. Double check the diameter of the cutter tip before reaming--some are oversize. To uniform the outside of the hole you can use the Sinclair 07-3000 outside PPC/BR flash hole reamer (right). This will ream the hole to about .064" or so to fit a standard 1/16" (.0625") decapping pin.

Seating Depth
When working with an untested load, we suggest starting .015" from the lands. However, our testing with multiple bullets in a 6BR rail gun shows that most 6mm match bullets bullets perform best seated to slightly jam, perhaps .010"-.015". However, this is not always true. We have observed that some of the heavier boat-tails, Sierras especially, perform best jumped by as much as .025". We've heard similar reports from the 6.5-284 shooters running 142 SMKs. But other guns perform better with bullets jammed in the lands .010" or more. You have to experiment to find out what works best.

Decapping
Before you can reload a case, you need to get the primer out. Lapua 6BR brass comes with a 1.50mm (.059") flashhole. Even the typical "small" decapping .0625" decapping pin will be too big. Yes, you might press it through the flashholes a few times, but evenutally you'll jam that .0625" pin and it will break. What's the answer? When you order 6BR sizing dies from Harrell's, Forster, or Redding, they should supply a decapping rod with .055-.057" tip diameter. But, we've found, sometimes all three companies don't do that and you have to call and ask for the right diameter. With something under .058" you'll have no trouble decapping those cases.

ballistol case lubeCase Cleaning and Lubrication
In a match chamber, with the modern propellents we have, your cases should come out of the chamber very clean. If you're operating in the "sweet spot" of the powder, you'll normally see a sine wave type powder pattern on the case neck. Don't worry--that is normal, and is a good sign. This editor does not tumble or wash cases. I use a dry nylon brush to clean inside the necks. I find a quick wipe with a patch sprayed with Ballistol Aerosol cleaner/lube will remove all the excess carbon on the outside of the case. (Tip: Wipe down the cases before you leave the range and the carbon hardens.) Ballistol, I've found, is also an ideal lubricant for full-length sizing of a small case such as the 6BR or 6PPC. Just spray a little Ballistol on your finger or wipe it on the case with a patch. Don't worry, Ballistol is non-toxic and bio-degradeable. It also wipes off very easily.

If you want to clean the inside of your cases, the best method is to clean with ultrasound. This does a superb job of removing carbon and powder residue from your brass inside and out. Jason wrote an excellent feature on Ultrasonic Case Cleaning. He experimented with various techniques and solvents and came up with an economical system that works great. If you haven't read Jason's article yet, Click HERE. One downside to ultrasonic cleaning is that it gets the brass so free of residues that you may need some extra lubrication in the necks to assist bullet seating. Jason recommends the dry moly lubricant sold by Neconos.com. (Without ultrasonic cleaning, the residual carbon/graphite residue left in the necks is all you need.)

Dies and Reloading Gear
Since the 6mmBR has recently become a very "hot" cartridge, all the major die-makers offer reloading dies. We like to use a full-length die that is a close match to our fired brass. One cost-effective way to get a "semi-custom" FL-sizing die is to send 2 or 3 fired cases to the Harrell Brothers at Harrell's Precision. They will select a full-length die (for use with neck bushings), that is a close fit to your case. The price, $70.00, is very reasonable, compared to full-custom dies.

Among factory 6BR sizing dies, it's hard to go wrong with a Redding Type 'S' full-length bushing die. This will both resize the case (and bump the shoulder) as necessary, and allow you to adjust neck tension with bushings. Alternatively, you can go with a body die, and a separate neck bushing die. The Forster Full-length die is also excellent, but you'll want to have the neck diameter increased by Forster.

If you load primarily one brand of bullets, another slick set-up is to buy a Forster full-length 6mmBR sizing die, and then send it off to Forster to have the neck honed for your desired amount of tension. Honing to .266" will give you about .002" of tension after springback. Forster charges just $10 plus shipping for this service. This elegant one-pass sizing solution produces very straight rounds with low run-out. We also believe that doughnuts (in the neck) form less readily if you full-length size with non-bushing dies as opposed to using bushings. Bushing dies leave a little bit of the neck unsized, and that's where the brass can build up.

For bullet seating, both the Redding Competition Seater and the Forster Ultra-Seater work great for the 6BR case. If you want the "Cadillac" of production seater dies for the 6mmBR, order the Wilson Stainless Micrometer seater from Sinclair Int'l, Grafs.com, or MidwayUSA.com (item 517603). Costing only a few dollars more than a Redding Comp seater, this die is a joy to use, providing very positive control over bullet seating depth. When used with a quality arbor press, the Wilson offers unrivaled "feel" for bullet-seating force. This can help you monitor neck tension, one of the most critical factors in maintaining low ES and SD for long-range accuracy.

Why the 6BR Will Continue to Grow in Popularity

I have to say that shooting and loading the 6BR is so rewarding that I can barely get motivated to shoot anything else. After all these years of .308 shooting in NRA Match Rifle, ISSF 300 Meter, NRA/CMP Service Rifle and Palma, discovering the accuracy, mildness and ease of loading of the 6BR is like striking gold. I feel like the William Hurt character in that now old movie The Big Chill who puts on a pair of sneakers for the first time in his life and is so overwhelmd by their comfort that he wears them 24/7.

German Salazar 6mmbr prone 6BR>It seems like everyone I shoot prone with is either shooting a 6BR now or planning to shoot one soon; it's a mini-revolution. The 6BR is no newcomer, so the sudden surge of interest over the past year has been somewhat of a surprise. Now, I'm not talking about 1000 yard shooting, but we shoot a lot of 500 and 600 yard prone matches and 300 meter matches also, both ISSF and NRA; and for these matches, I've concluded, as apparently have many others, that the 6BR is hard to beat.</p>

<p>For a long time the .308 was the true

The 6BR exhibits all these same characteristics and a few more pleasant ones as well, such as low recoil and accuracy even exceeding the .308--which is nothing to sneeze at! When I had my first 6BR put together, my intention was to use it strictly for 300 meter shooting; I didn't believe it would be effective at 600 yards. Then, one afternoon, I happened to shoot 30 rounds of leftover ammo at 600 yards from the 6BR. The first shot hit low with my guessed-at zero. The remaining 29 shots were twenty-one Xs and eight 10s. That wiped the sleep from my eyes and a fair number of rifles in my safe suddenly looked very old-fashioned. When "everyone" shot a .308 both in bolt guns and in service rifles, there were a number of different loads for different purposes/distances, etc. However, if your rifle wouldn't shoot decently with 40 to 41 grains of IMR 4895 and a Sierra 168, it was time for a visit to the gun doctor.

Similarly, every 6BR that I've dealt with will shoot 30 grains of Varget and a 105- to 108-grain bullet (bare or moly) very well indeed. While charge adjustment for the particular lot of Varget is a must, and seating depth fiddling is always useful, the basic load is there: 30.0 Varget and a 105--if it won't shoot that, it isn't the load's fault.

6mm Benchrest BR RemingtonI don't think too many years will pass before we see the 6BR as the truly dominant cartridge in US prone shooting (other than 1000 yards) just as it is already the dominant cartridge in Europe for 300 meter shooting (though the 6XC in Norma brass did well this year). The fact that the 6BR has already spawned a number of wildcats (Dasher, 6BRX, 6BRDX) shows the extent to which people recognize its accuracy while still seeking a little more speed in our classical American way. Still, I think it's the basic, standard 6mmBR cartridge that we'll see at the top of the heap.

Finally, while the useful brass is European (Lapua and Norma) and it was largely European shooters who popularized it, the 6BR is an All-American cartridge. The 6BR was developed by benchrest shooter Jim Stekl, a Remington engineer who chafed at shooting the 6PPC (based on a Russian service cartridge) and wanted a US-born rival. While the 6BR never did tear up the Benchrest world, Stekl may yet get the last laugh as it takes over Highpower prone--a much bigger sport.  German Salazar, ShootersJournal.com

Favorite 6BR Accuracy Loads for 80gr to 108gr Bullets
Favorite Recipes
There is no "screamer" load that works in every rifle. Some barrels prefer Bergers, others Sierras or Lapuas. Powder lots vary considerably--this will affect your max velocity and tune. Your barrel twist will also dictate the bullets you can run--you'll need an 8-twist to run the heavy (105-108 grain bullets). The Berger 95 VLDs normally demand a 1:9" or faster. The Sierra and BIB 95s will work in a 10-twist. Bore dimensions can also have an effect. We've found the Lapua 105s, which are "skinnier" than Berger or Sierra 105s, often prefer bores which run on the "tight" side. But still, here are some proven loads that should get you shooting bugholes.

WARNING: With all loads, ALWAYS START 10% LOW and work up incrementally.
BulletMfgGrainsPowderPrimerFPSComments
80gr FBBerger/Fowler30.0VV N135Fed 205m3150Outstanding accuracy in 1:12" or faster twist. Start .015" into lands. Great 200/300m load.
88gr FB LoDragBerger31.0VargetCCI BR43100A bit finicky to tune--depth sensitive, but can be super accurate. Good in Dasher too.
90gr ScenarLapua33.0 (moly)VV N540CCI BR43050Very uniform bullet, works in or out of lands. Superb "short-line" bullet for Cross-course.
95gr FBBIB30.7VargetCCI 4502980Like a laser in a true 10-twist or faster. Quarter-MOA at 200m. Keep 'em under 3100 fps.
95gr VLDBerger31.0VargetCCI BR43000Great combo of speed, BC, and accuracy, but can be finicky. Sort bullets by bearing surface and jam 'em.
95gr VLDBerger31.3VargetCCI 4503060Jammed .012" in lands this shot in the ONEs in a PacNor 0.236 3-groove. 150 fps faster than Berger 108s.
103gr BTSpencer30.5RL 15CCI 4502920+NEW shorter boattail design. JLK Jackets. Tight meplats. Very uniform. Good choice for 1K.
105gr
A-Max
Hornady29.0H4895CCI BR42840H4895 is very accurate, low ES/SD. Kyle Brown used a hotter version of this load to set his 1K record group.
105gr
BT Match
Berger29.5H4895CCI BR42880J. Schmidt's recommended "moderate" accuracy load for factory actions. Very accurate and consistent. 1/4 MOA 25-shot Agg at 200.
105gr ScenarLapua30.3Norma 203BCCI BR42901Very Accurate. Extremely low ES=7/SD=3 at .012" in lands. Powder IS Temp sensitive. 30.5 also very accurate with .020" jam. BUT may be hot. Start low (29.5gr) with 203B.
105gr ScenarLapua30.3VargetCCI 4502920+Very uniform bullet that likes tight bores or canted lands. You can hot up this load in winter by .3 grains. Match load, .015" into lands.
105gr ScenarLapua30.5+VV N150CCI BR42950+In a BAT action, Jackie Schmidt runs the Scenars close to 3K with N150. Super accurate in a .236-land Krieger. Work up carefully.
105gr VLDBerger31.5IMR 4007sscCCI 450n/aWith VLDs jammed .015 this shows very tight vertical at 200. 100% load density.
105gr VLDBerger30.4VV N540CCI 4502900+Terry Brady has set world records with moly version of this load (31.0 gr), and RL15 works too. Great bullets. High BC.
106gr BTClinch River30.4RL 15CCI 4502920Jason's World Open-winning bullet/powder. The CR 106s are superb. Ultra-accurate with minimal vertical. There is a higher node too.
107gr BTSierra30.0VargetFed 205m2885Classic accuracy load for the 107 SMKs. Works well in many guns. You can hot it up, but start at 30.0. Try Wolf (Russian) primers too.
108gr BTBerger30.5VargetCCI BR42900+NEW bullet. This load has tested 1/4 MOA at 550 yards. You can substitute RL 15, but it is more temp sensitive.

Velocity estimates are for 28" 8-twist barrel. Velocities will vary up to 90 fps from barrel to barrel, and with different powder lots.

Comparative Ballistics (Drop from 100yd Zero, Drift in 10 mph Crosswind)
CartridgeBulletVel FPS300yd Drop/Drift600yd Drop/Drift1000yd Drop/Drift
6mm BR105 Berger VLD292010.91" | 5.08"73.33" | 22.35"286.0" | 71.4"
6mm Dasher105 Berger VLD30309.92" | 4.85"67.33" | 21.24"262.7" | 67.4"
6XC115 DTAC30409.67" | 4.41"64.82" | 19.01"247.2" | 59.5"
.243 Win115 DTAC31208.97" | 4.24"60.82" | 18.25"232.3" | 57.0"
.243 AI115 DTAC32008.32" | 4.08"57.15" | 17.57"218.6" | 54.8"
Drop and Wind-Drift calculated with Point-Blank Software for 70° F temp, and 1000' altitude. BCs were 0.585 for 115 DTAC, 0.535 for Berger 105 VLD.

Factory Reloading Data
WARNING: With all loads, ALWAYS START 10% LOW and work up incrementally.
Accurate Arms (.pdf file) Alliant Powder Hodgdon Powder IMR Powder Vihtavuori (.pdf file)
WARNING: ALWAYS start 10% below these loads and work up. Pressures can vary dramatically from one barrel to another. Seating depths have a huge effect on case pressures--moving the bullet just .015" one way or another can push a "safe" load into the danger zone. Powder lot variances can be extreme--you may have to adjust a full grain or more. Whenever you buy new powder, even the same brand, start 10% low. NEVER assume pressures will be safe if you change lots or ANY component. Case web growth is probably the most reliable indicator of over-charge. By the time you're getting stiff bolt lift or ejector marks with fresh brass you've exceeded proper pressure levels. Ambient temperatures can alter pressures considerably. Don't assume cold weather loads are safe in summer. As you approach max loads, reduce the load increments. Just 0.2 grains can make a difference.

6mmBR Frequently Asked Questions (FAQ)

  • What is the 6mm BR?
  • What Kind of Accuracy Can I Expect?
  • Which is Better -- 6mm BR or 6PPC?
  • What Brass Should I Use?
  • What Size are Lapua 6BR Flash-Holes and Should I Ream Them Larger?
  • What is the Correct OAL for the Case?
  • What Barrel Twist Do I Need?
  • Tight Neck or No-Turn Neck -- What's Best?
  • What Is Recoil Like on a 6BR?
  • Does Anybody Sell Factory-Loaded Ammo?
  • Can I Buy a Production Rifle Chambered in 6mm BR?
  • What is the 6mm BR?
    The 6mm BR that is most commonly used today is also called 6mm Norma BR, "6BR Norma", or just plain "6BR". Norma started with the 6mm Remington Benchrest and increased the base dimension slightly. But the official SAMMI cartridge OAL is the same: 1.560". (However Remington did originally produce brass at 1.520" OAL and some older chambers have been cut to a shorter length.) Though Norma standardized the round, most people shoot Lapua brass, because of its superior quality and uniformity, not to mention lower cost. The case capacity of Lapua brass is about 38-39.5 grains of H20, after fire-forming. The exact capacity depends on your gun's chamber and the brass lot.

    What Kind of Accuracy Can I Expect?
    The 6mm BR is one of the most accurate cartridges in existence, bettered only by the 6 PPC and 22 PPC. A well-built rifle with a match-grade barrel should deliver consistent 5-shot groups in the 2s at 100 yards with flat-based bullets. If you get lucky, perhaps it will group in the 1s. European shooters firing Norma 6mm BR loaded ammo in Sauer factory target guns report .3 moa accuracy at 300m. 600-yard match shooters are getting sub 3" aggregates in real world conditions, shooting 100gr bullets in 1:8 twist barrels.

    Which is Better -- 6mm BR or 6PPC?
    Both are extremely accurate and efficient cartridges. The 6BR shares the short/fat case design and small primer hole that make the 6PPC so accurate. In 100-200yd benchrest competition, the 6PPC is still the "winningest" cartridge around. However, the 6mm BR is superior at 300m and beyond. With more case capacity, the 6mm BR can drive the heavier, higher BC bullets needed at long distance. With the 6PPC you have to turn necks and fire-form the cases from smaller 220 Russian brass. That's lots of work. Conversely, Lapua 6BR brass shoots great right out of the box. Bottom line: the 6PPC may be a tiny bit more accurate at short ranges, but the 6mm BR is easier to load and shoot, and is incredibly accurate all the way out to 1000 yards. In fact, the current ten-shot 1000yd world record was set with a 6mm BR.

    What Brass Should I Use?
    Use Lapua brass. None better. Make sure your gunsmith chambers for the Lapua brass dimensions, not 6mm BR Remington brass or Norma brass. Some lots of the Lapua are very slightly larger at the base than Norma. If you have a barrel tightly chambered for Norma brand brass, Lapua brass should fit if you use a small base size die. The tight spot is at the web of the case--it may be just a tiny bit larger diameter than the Norma. But the Norma brass is very good. It's just a good deal more expensive than Lapua from most vendors. Current lots of Lapua 6BR brass measure .2685"-.269" neck diameter with a bullet seated and .469" right at the web of an unfired case. We've seen some of the Lapua brass has a bit of a flare right at the mouth which means that a .271" neck might be too tight. Setting the neck for .272" is a pretty safe bet for current lots of Lapua brass. Here is Lapua's current specification:

    What Size are Lapua 6BR Flash-Holes and Should I Ream Them Larger?
    When Lapua started making 6mm BR Norma brass ten years ago, Lapua adopted a 1.50mm (0.059") flash hole size. However, Lapua tells us that production tolerances run up to 1.60mm (.063"). OK, should you ream your flash-holes to fit a standard 1/16" (.0625") decapping rod? We suggest NOT reaming. First you have to buy special tools, and you may end up with flash-holes that are bigger than you want. If you use the K&M PPC flash hole deburrer to ream the hole (from the inside) it will end up about 0.068". If you use the Sinclair 07-3000 tool (which reams from the outside), shown below, the flash-hole will end up about 0.063". The later is probably OK, but when you start to approach 0.070" we think you may be losing some of the claimed accuracy advantage of the small PPC-style flash-hole.
    If you want to leave your 6BR flash-holes at minimum diameter, turn down your 1/16" decapping pins or decap with a Redding or Harrell's die. The 6BR and 6PPC Redding and Harrell's dies normally ship with a .057" diameter decapping pin. (If yours is larger, ask Redding for the smaller version.) The .057" decapper will work with UN-REAMED 6BR brass. So, to make a long story short, flash holes anywhere from .059"-.063" are "normal" and a Redding die should work. But if you want to use a 1/16" (.0625") decapping pin (found on most "universal" decapping dies) you should ream with the Sinclair 07-3000 tool. UPDATE: Recent lots of Lapua 6mmBR brass have shown a little sliver of brass that can occlude the flash-hole. You will want to remove this excess brass so that the flash-hole is clear. You can do this with an inexpensive "pin-vise" and #53 (.0595") drill bit.

    What is the Correct OAL for the Case?
    New Lapua brass measures 1.556-1.557". CIP spec for the 6mm BR Norma case is 1.5598". The SAAMI OAL spec for 6mm BR Remington is 1.560", essentially the same. However Remington originally produced the brass at 1.520" OAL, and some older reamers reflect this shorter length. If you have an older rifle you probably want to have the neck extended to shoot modern brass, with 1.560" max length. The Lapua brass is headstamped 6mm BR Norma-Lapua. We trim all our cases to 1.555" when any one reaches 1.560" or longer.

    What Barrel Twist Do I Need?
    The most versatile barrel is a 1:8 twist, from 26" - 28". This will shoot everything from 65gr FB bullets to 107 VLDs with great accuracy. For shooting out to 600 yards, in calm conditions, you may get best accuracy with custom 80-90gr FB bullets. These work best in a 1:12 twist tube. So far, the 1:10 twist has been a "tweener" that hasn't been as popular as a 1:8 or 1:12. On paper, the 1:10 should do well with the new low-drag FB bullets, and most 90gr boat-tails. The 95gr Berger VLD requires at least a true 1:9. But right now, when most people buy their first 6mm BR barrel, they chose a 1:8.

    Tight Neck or No-Turn Neck -- What's Best?
    The collective wisdom is evolving on this issue. Originally, 6BR shooters emulated what works for the 6PPC--tight .262" necks with a .009" or so neck wall thickness. Now the trend is in the other direction. Many shooters have had great success with .268-.269" necks that allow full neck uniforming with a cut up into the shoulder to block the formation of doughnuts. That said, we are now seeing very accurate rifles being built with .271-.272" and even .274" chambers that allow Lapua 6mm BR brass to be loaded and shot with no neck-turning. The results have been encouraging to say the least. Richard Schatz recently set a 1000-yard world record with a .271"-necked 6mm Dasher. And there is evidence that the longer VLD bullets work best with the greater neck tension allowed by unturned or minimally-turned brass. One well-known shooter says he has seen no loss of accuracy since changing to no-turn necks, and that's how he will chamber all his future barrels. However, most top smiths still recommend turning necks, but not down to .262". A .269" chamber appears to be a good compromise, allowing a quick, easy one-pass turn without sacrificing beneficial neck tension. For a varmint or tactical rifle, the choice is clear, however--go with a no-turn neck so you can spend more time shooting and less time reloading. Both the Lapua and the Norma brass are good enough that you will give up very little accuracy.

    What Is Recoil Like on a 6BR?
    Recoil is mild. A 17-lb 6BR recoils less than a standard 9-lb AR15. Compared to a .308 rifle of equal weight, the 6BR has 55% less recoil, and the 6BR's movement is much less snappy. By the numbers, a 17-lb 6BR rifle shooting a 100gr bullet at 2950 fps recoils at 3.74 fps, with 3.7 ft/lbs of recoil force. By contrast, a 17-lb .308, shooting a 168gr SMK at 2700 fps, recoils at 5.59 fps, with 8.25 ft/lbs of recoil force.

    Does Anybody Sell Factory-Loaded Ammo?
    Yes, both Lapua and Norma sell extremely high-quality 6mm BR loaded ammunition. This is super-premium stuff, made for 300m competition. Lapua offers a 77gr HP round, plus 90gr and 105gr cartridges loaded with Scenar BTs, either moly or naked. Norma offers one product--the 6mm BR Diamond Line, loaded with a 105gr moly-coated Berger bullet. Full review.

    Can I Buy a Production Rifle Chambered in 6mm BR?
    Very few factory rifles are available in the United States chambered in 6mm BR, either the old 6mm Remington BR version, or the newer version we call 6mm Norma BR. Savage does offer two models chambered in 6BR and they are both winners. The F-Class Savage 6BR features an 8-twist, 30" barrel and heavy BR stock with 3" fore-arm. Terry Brady has tested this rifle for us and it shot well under 1/2 MOA out to 300 yards. Expect to pay about $1050.00 retail for the Savage 6BR F-Classer. Savage also offers a 12-twist Long-Range Precision Varminter fitted in a hunting-style stock. Blaser does offer a single-shot version of its straight-pull target rifle in 6mm Norma BR, and Sig-Sauer offers 6mm Norma BR single-shots in their European-market target rifles. These are not currently being imported into the United States, however. Among limited-production American-made guns, the Cooper Arms Model 22, the Remington 40XB (Custom Shop), and the Tubb 2000 are all available in a 6mm BR chambering.

    6mmBR at Long Range--Beware Baney's Giant Killer

    Can the diminutive 6BR work at long range--even out to 1000 yards? You bet. Just ask Jason Baney, our 1000-yard Editor. In 2006, Jason shot his 16-lb Lowrider-stocked standard 6BR in the Heavy Gun Class at the Williamsport World Open. Competing against cartridges burning more than twice as much powder and rifles weighing up to 100 pounds, Jason's little 6BR proved to be a giant killer--a David slaying the Goliaths. Jason won the Heavy Gun title, using the standard 6BR case and Clinch River 106gr bullets. And get this, he used unturned Lapua brass, with almost no case prep. As Jason says "the 6BR may give up something in the wind vs. the Big Boomers, but when it comes to pure accuracy and holding tight vertical, this little case can do the job."

    Jason Baney 6mmBR 6BR World Open Heavy Gun

    Favorite Varmint Loads for 40gr to 87gr Bullets
    WARNING: With all loads, ALWAYS START 10% LOW and work up incrementally.
    Size Bullet Powder Load Primer Case BC Velocity Comments
    55

    Sierra BlitzKing

    H322 28.9 Rem 7.5 Lapua Std .225 3200 Sierra's Accuracy Load. 31.5gr H322 clocks 3400 fps with CCI BR4.
    55 Nosler Ballistic Tip AA XMR-2015 32.0 Fed 205M Lapua Std .276 3700 Explosive hunting load with excellent accuracy and velocity.
    55 Nosler Ballistic Tip Benchmark 32.6 CCI BR4 Lapua Std .276 3600 Good accuracy + long case life. "H322 or AA2010 may be a bit more accurate but they're hard on cases."
    58    Hornady V-Max AA 2230 30.5 Fed 205M Lapua Std .250 3600 (max) Start LOW!! Work to 32+ grains MAX. Meters well on progressive press (Dillon). Lot to lot variations.
    60 Berger FB H335 32.0 Fed 205m Lapua Std .242 3650 Gene Harwood set 100yd record with 6BR shooting his own 60gr HP at 3700 fps with max H335 load. Great speed + accuracy.
    60 Berger MEF H322 31.0 Rem 7.5 Lapua Std .241 3400 Accurate and "the MEF bullets really clobber varmints."--Steve Timm
    65    Hornady  V-Max VV N135 33.0 Fed 205M Lapua Std .280 3350 "[This load] shoots .25MOA easily and sends critters flying".
    68 Bart's FB High 7 H322 29.6 Fed 205M Lapua Std n/a 3215 "Shoots extremely well for me--very accurate, with ten-shot ES of 11."
    68 Berger FBHP Varget 34.2 CCI BR4 Lapua Std .276 n/a "Consistently my best load, and [I've tried] Sierra 55gr BKs and 70gr HPs, plus V-Maxs in 58, 65 & 75gr."
    69 Berger Low Drag VV N135 29.3 CCI BR4 Lapua Std .321 3000 Excellent, mild 300m accuracy load.
    70 Nosler Ballistic Tip VV N135 32.7 Fed 205M Lapua Std .310 3300+ "My best 6BR varmint load so far. Jump the Noslers .010-.015."
    70 Sierra BlitzKing

    AA2460

    33.0

    Rem 7.5 Lapua Std .299 3275 33gr AA2460 is a classic Varmint load. 31.2gr Benchmark (3200 fps) is also effective
    74 Berger FBHP Varget 33.3 Rem 7.5 Lapua Std .292 3200+ "[I've shot] the 74 Bergers in my 1:14 barrel for 15+ yrs--love this load"
    75 Hornady V-Max Varget 32.8 CCI BR4 or 400 Lapua Std .330 3300 Shoots in the Twos in 12-twist barrel. Try .010" jam or .010" jump.
    75    Hornady  V-Max VV N135 31.5 Fed 205M Lapua Std .330 3300 A near-perfect bullet for the 6BR case capacity. Varget also works great.
    75 Sierra FB Varmint Benchmark 31.2 Rem 7.5 Lapua Std .217 3200 Inexpensive yet very accurate bullet. Sierra's Accuracy Load is 29.3gr VV N135, 3000 fps.
    80 Berger HP H4895 30.0 Rem 7.5 Lapua Std .314 3100 Very accurate bullet at a good price. Start low with surplus 4895 powders.
    80 Berger Varmint Varget 31.8 Rem 7.5 Lapua Std .278 3120 More speed possible, but start low and watch pressures above 3100 fps.
    80 Berger Varmint VV N135 31.5 CCI 450 Lapua Std .278 3242 Super-accurate in Pac-Nor 3-groove. Sub-quarter MOA. Pretty hot load.
    80 Fowler FBHP VV N140 32.5 Rem 7.5 Lapua Std n/a 3120 "Tried Varget, Benchmark, N135, N140. All shot well. N140 gave 3120fps, ES of 9, so that's my pick."
    87    Hornady  V-Max Varget 31.0 CCI 450 Lapua Std .400 3050 Very accurate bullet with good BC. 3100+ fps in a 27" 10-twist with a bit more powder. Target Photo.
    Velocities are based on a 25" barrel and standard 6mmBR Norma case. Note, velocities may vary considerably from gun to gun, and even barrel to barrel. Primer brand will also alter velocities. Always start 10% low and work up.

    WARNING: With all loads, ALWAYS START 10% LOW and work up incrementally.

    6mmBR Factory Ammo: Half-MOA or Better Out of the Box

    Just how good is the factory-loaded 6mm BR ammunition from Lapua and Norma? Well, it's good enough to set World Records in 300m competition. Even the most skilled handloader may be hard-pressed to produce more accurate loads. Our initial test with the 90gr Lapua ammo showed it can deliver 0.3 MOA at 100 yards from a good gun. At the 2003 Europe Cup in Switzerland, Juha Hirvi used Lapua ammo to set a new European and World Record: 1,180 points (400+387+393). And Norma Diamond Line 6mm BR ammo has won CISM 300m championships multiple times.

    lapua factory 6mmbr ammo Solveig Bibard Europa Cup
    Factory LoadBulletFPSm/sec
    Lapua Match90gr Scenar moly3050930
    Lapua Match105gr Scenar2789850
    Norma Diamond Line105gr Berger LTB moly2789850

    3050 fps from Lapua's 90gr Factory Load -- Great Choice for 600yd BR
    Lapua offers factory ammo loaded with 90gr and 105gr Scenars. Lapua claims 3050 fps for its 90gr molys and 2950 fps for 90gr naked Scenars (26" barrel). The Lapua 90gr round would be our first choice at 600 yards in steady winds. We think the extra 260 fps over the 105gr version is worth the slightly lower BC (.420 vs. .530 for the 105gr Scenar), and the 90gr Scenar should be very accurate in a 1:10 twist barrel. We plan to test the 90gr Lapua Factory ammo at 600yds and see if this factory 90gr round can compete with handloads, right out of the box. Lapua ammo is available from Graf's for about $26 per box of twenty (20) loaded rounds: 90gr moly Scenar, Graf's Item LU4316045; 105gr moly Scenar, Graf's Item LU4316046. Below are specifications for the Lapua 90gr and 105gr factory-loaded ammo:

    lapua 6mmbr factory ammunition

    Factory Ammo That Shoots .42 moa at 300m -- Impressive Indeed
    While you can achieve somewhat higher velocities with custom hand-loaded ammo, we think the factory-loaded match ammo is good enough to win 600yd matches at the club level and that's saying a lot. Components are top of the line. Brass is excellent as are the bullets. Norma uses moly 105 Berger LTBs while Lapua uses its own 105 Scenars (moly or naked). The Scenar enjoys an edge in BC, because Berger's length-tolerant-bullet design is a bit shorter to aid feeding from magazine. So the Lapua ammo may work a little better in the wind, but the Norma may have an edge in pure accuracy in steady conditions. Click on this Norma Diamond Line 300m test target. That's 10 rounds, recorded by an electronic target. The 3.5cm (1.38") group works out to .42 moa. And check out this Norma 60-round 300m test target. Will your handloads do better than that, even shot from sandbags? Maybe not. Unfortunately, though widely available in Europe, this Norma ammo is very hard to obtain right now in the United States.

    Lapua Importer:
    Kaltron Pettibone Inc.
    1241 Ellis Street
    Bensenville, IL 60106
    Phone: (630) 350-1116
    www.kaltron.com
    Lapua Distributor
    Graf & Sons
    4050 S. Clark
    Mexico, MO 65265
    Phone: (800) 531-2666
    www.Grafs.com
    Norma Distributor:
    Black Hills Shooters Supply
    2875 S. Creek Drive
    Rapid City, SD 57709
    Phone: (800) 289-2506
    BHShooters.com

    Topics: 6mmBR.com, AccurateShooter.com, 6BR, 6mm BR, 6mm BR Norma, 6BR Improved, 6mm Dasher, 6mm BRX, 6mm BRDX, 6mmBR UBL, 6BRBS, 6mm Remington Benchrest BR, 308 boltface, .308 Winchester, 308 Win, Reloading, Bullets, Berger, Lapua, Norma, Winchester, Remington, Speer, Hornady, Partition, Nosler, Sierra, MatchKing, Blitz, BlitzKing, V-Max, Vmax, hollow point, boattail, boat-tail, BT, HPBT, powder, gunpowder, H414, Varget, H4350, IMR, IMR 4064, IMR 4350, Alliant Powders, Reloader 15, RL 15 Reloader 19, Vihtavuori, N160, N-160, N165, N-140, N150, brass, Load Map, Reloading Recipes, WLR, CCI Primer, CCI BR2, Federal Primer, Fed 210, 210m, Savage 12-BVSS, Cooper Firearms, Savage.

    Copyright ? 2007, 6mmBR.com | AccurateShooter.com, All Rights Reserved.
    No reproduction without advanced permission in writing.

    free hit counter



    Support Our
    SPONSORS

    Site Meter