HOME

Ponizej zamieszczam kompletny ekranowy zrzut BOOT + DEBUG  and POWEROFF playera

Below is full screen dump BOOT + DEBUG and POWEROFF of player:

START <PLAYER POWERON>
BCM76300010
Setting NAND Params

CFE starting from ROM
Chip specific init
TLB init
Board init
Starting memory configuration
Valid memory config = D3128256
Disable refresh - set byte lane 8
Setting up PLL
Setting up memory controller
Enable DDR encryption
SoooooooooooooR
Preparing to copy code to RAM
Prepare for NAND loading


Starting code in RAM
Booting Secured CFE...


BCM97630 B0-SEC-lg8_100126r0  CFE v2.11.10 (CFE core v2.11, BSP_REV 10), Endian Mode: Little
Build Date: 2010. 01. 26. () 11:36:34 KST (khy2766@nexus)
Copyright (C) Broadcom Corporation.


*jjc* PROD_REVISION is 0x76300010
*jjc* is 7630

DDR                        : Bank0:128MB@667MHz | Bank1:256MB@667MHz
NAND Boot                  : FlashSize 256MB on CS0, BlkSize 128KB, PgSize 2048B
NAND vendor timing         : 98da9015 Toshiba TC58NVG1S3ETA00 SLC  t1(33535233) t2(80000b98)
Secure boot                : Enabled
Port lock                  : Enabled

doupdatecheck: nothing new and no try_count

Timestamp started ...
booting ARM...
Reading flash0.ofefw.1 to V:0x80000000 from offset 0 len 1048576
validating ofe fw_ldt@0x800fffb0 ...
parsed fw_ldt@800fffb0 : ws0_sadr=0xc0000 ws0_eadr=0xdffff prodid:BD READER R02
parsed fw_ws @800c0000 : vendor: LGH08SAN prodid: LG H08SAN BC7630
Reading flash0.ofews.1 to V:0x80100000 from offset 0 len 131072
parsed  WS@80100000 :  Vendor:LGH08SAN Prodid:LG H08SAN BC7630
updating fw_ws@800c0000 with flash0.ofews.1
ws was updated in the fw image succesfully
booting ARM...ofefw@0x2fd00000
done

Elapsed time  263mS (263395 uS)


Automatic startup canceled via Ctrl-C
CFE> ^C
CFE> printenv
Variable Name        Value
-------------------- --------------------------------------------------
        BOOT_CONSOLE uart0
         ETH0_HWADDR E8:5B:5B:A1:48:0D
             STARTUP splash -576p; boot -z -elf flash0.kernel: 'root=/dev/romblock10 ro rootfstype=squashfs videotype=PAL memcfg=384 OFE_SB=y quiet console=0,115200n8'
         CFE_VERSION 2.11.10
       CFE_BOARDNAME BCM97630 B0-SEC-lg8_100126r0
      CFE_MEMORYSIZE 128
*** command status = 0
CFE> ^C
CFE> splash -576p; boot -z -elf flash0.kernel: 'root=/dev/romblock10 ro rootfstype=squashfs videotype=PAL memcfg=384 OFE_SB=y verbose debug console=0,115200n8'
Display splash screen
Using valid user input parameters - Resolution 576p on Component
[ Default Video ] :  Current Video Output : Component @ Resolution : 576p
Loading PAL SD image to 0x06646c00 size 829440 bytes
Reading flash0.splash to V:0xa6646c00 from offset 4838400 len 829440
Done displaying splash screen
Reading flash0.splash to V:0xa6e00000 from offset 5667840 len 44
Loader:elf Filesys:raw Dev:flash0.kernel File: Options:root=/dev/romblock10 ro rootfstype=squashfs videotype=PAL memcfg=384 OFE_SB=y verbose debug console=0,115200n8
Loading: 0x80008000/5427744 0x80535220/1327744
Successfully loaded secure elf image....
Entry address is 0x8000c330
Starting program at 0x8000c330

[    0.000000] get_cfe_boot_parms returns 0, strlen(cfeBootParms)=110
[    0.000000] found console=  0 <0,115200n8>
[    0.000000] Number of Nand Chips = 0
[    0.000000] Kernel boot options:  root=/dev/romblock10 ro rootfstype=squashfs videotype=PAL memcfg=384 OFE_SB=y verbose debug console=0,115200n8
[    0.000000] ES bit: CP0 $16 sel 7 B4 = 00000100
[    0.000000] ES bit: CP0 $16 sel 7 after = 00000100
[    0.000000] CPU revision is: 0201937c (MIPS 24Kc)
[    0.000000] early_tlb_init: tlb size 64
[    0.000000] get_memory_config: Take memory configuration from CFE HWinfo
[    0.000000] -- DDR Bank 0: 128 MB
[    0.000000] -- DDR Bank 1: 256 MB
[    0.000000] set_memory_config: memory config = 384
[    0.000000] ddr_banks: 2 size 384Mb (0x18000000)
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000]  memory: 10000000 @ 20000000 (usable)
[    0.000000] BMEM region 0: 0x02800000 - 0x08000000 size 0x05800000
[    0.000000]     Added to reserved bootmem
[    0.000000] BMEM region 1: 0x23900000 - 0x2fd00000 size 0x0c400000
[    0.000000] BMEM region 2: 0x2fd00000 - 0x30000000 size 0x00300000
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00020000
[    0.000000]   HighMem  0x00020000 -> 0x00030000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00008000
[    0.000000]     0: 0x00020000 -> 0x00030000
[    0.000000] On node 0 totalpages: 98304
[    0.000000]   Normal zone: 0 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000]   HighMem zone: 0 pages used for memmap
[    0.000000]   HighMem zone: 65536 pages, LIFO batch:15
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] ######### SUN_TOP_CTRL_SW_RESET @b0404014 = 00000000
[    0.000000] Linux version 2.6.28.9 (ykhong@hyori) (gcc version 4.2.0 20070124 (prerelease) - BRCM 10ts-20080721) #189 Thu Jan 28 18:54:14 KST 2010
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 24832
[    0.000000] Kernel command line: root=/dev/romblock10 ro rootfstype=squashfs videotype=PAL memcfg=384 OFE_SB=y verbose debug console=0,115200n8
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00058004
[    0.000000] Readback ErrCtl register=00058004
[    0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[4294667.296000] console [ttyS0] enabled
[4294667.297000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[4294667.298000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[4294667.348000] Memory: 89096k/89496k available (3800k kernel code, 303720k reserved, 1322k data, 176k init, 58368k highmem)
[4294667.349000] SLUB: Genslabs=10, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[4294667.350000] Calibrating delay loop... 339.96 BogoMIPS (lpj=169984)
[4294667.372000] Security Framework initialized
[4294667.373000] DIGSIG MODULE - Initializing module
[4294667.374000] DIGSIG: no valid key, digsig security disabled
[4294667.375000] Mount-cache hash table entries: 512
[4294667.377000] PM: Adding info for No Bus:platform
[4294667.378000] net_namespace: 288 bytes
[4294667.379000] NET: Registered protocol family 16
[4294667.380000] PM: Adding info for platform:ehci-brcm.0
[4294667.381000] PM: Adding info for platform:ohci-brcm.0
[4294667.385000] PM: Adding info for No Bus:default
[4294667.386000] SCSI subsystem initialized
[4294667.387000] libata version 3.00 loaded.
[4294667.388000] usbcore: registered new interface driver usbfs
[4294667.389000] usbcore: registered new interface driver hub
[4294667.390000] usbcore: registered new device driver usb
[4294667.394000] PM: Adding info for No Bus:mem
[4294667.395000] Switched to high resolution mode on CPU 0
[4294667.400000] PM: Adding info for No Bus:null
[4294667.404000] PM: Adding info for No Bus:zero
[4294667.409000] PM: Adding info for No Bus:full
[4294667.413000] PM: Adding info for No Bus:random
[4294667.418000] PM: Adding info for No Bus:urandom
[4294667.423000] PM: Adding info for No Bus:kmsg
[4294667.427000] PM: Adding info for No Bus:lo
[4294667.432000] NET: Registered protocol family 2
[4294667.445000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[4294667.452000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[4294667.459000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[4294667.466000] TCP: Hash tables configured (established 4096 bind 4096)
[4294667.473000] TCP reno registered
[4294667.479000] NET: Registered protocol family 1
[4294667.483000] init_ar_checker _stext 0x80008000 _etext 0x803be0d8
[4294667.490000] checker_0 control 0x00000008 addr low 0x00001000 hi 0x003be000
[4294667.497000] read rights _0 0xffffffff _1 0xffffffff write rights _0 0x00000000 _1 0x00000000
[4294667.505000] checker_1 control 0x00000008 addr low 0x003bf000 hi 0x027fff80
[4294667.513000] read rights _0 0xffffffff _1 0xffffffff write rights _0 0x00000000 _1 0x00e4f8a0
[4294667.521000] checker_2 control 0x00000008 addr low 0x20000000 hi 0x238fff80
[4294667.529000] read rights _0 0xffffffff _1 0xffffffff write rights _0 0x00000000 _1 0x00e4f8a0
[4294667.537000] checker_3 control 0x00000010 addr low 0x2fd00000 hi 0x2fdfff80
[4294667.544000] read rights _0 0xffffffff _1 0xffffffff write rights _0 0x00000000 _1 0x00010000
[4294667.553000] power_init power_debug 0
[4294667.557000] power_init: major device number 0
[4294667.563000] squashfs: version 3.4 (2008/08/26) Phillip Lougher
[4294667.570000] NTFS driver 2.1.29 [Flags: R/O].
[4294667.574000] msgmni has been set to 60
[4294667.580000] io scheduler noop registered
[4294667.584000] io scheduler deadline registered (default)
[4294667.590000] PM: Adding info for No Bus:tty
[4294667.594000] PM: Adding info for No Bus:console
[4294667.599000] PM: Adding info for No Bus:ptmx
[4294667.603000] Serial: 8250/16550 driver4 ports, IRQ sharing disabled
[4294667.610000] PM: Adding info for platform:serial8250
[4294667.615000] serial8250: ttyS0 at MMIO 0x0 (irq = 65) is a 16550A
[4294667.621000] PM: Adding info for No Bus:ttyS0
[4294667.626000] serial8250: ttyS1 at MMIO 0x0 (irq = 66) is a 16550A
[4294667.632000] PM: Adding info for No Bus:ttyS1
[4294667.637000] serial8250: ttyS2 at MMIO 0x0 (irq = 67) is a 16550A
[4294667.643000] PM: Adding info for No Bus:ttyS2
[4294667.648000] PM: Adding info for No Bus:ttyS3
[4294667.652000] PM: Adding info for No Bus:ram0
[4294667.657000] PM: Adding info for No Bus:1:0
[4294667.661000] PM: Adding info for No Bus:ram1
[4294667.666000] PM: Adding info for No Bus:1:1
[4294667.670000] PM: Adding info for No Bus:ram2
[4294667.675000] PM: Adding info for No Bus:1:2
[4294667.679000] PM: Adding info for No Bus:ram3
[4294667.684000] PM: Adding info for No Bus:1:3
[4294667.688000] PM: Adding info for No Bus:ram4
[4294667.693000] PM: Adding info for No Bus:1:4
[4294667.697000] PM: Adding info for No Bus:ram5
[4294667.701000] PM: Adding info for No Bus:1:5
[4294667.706000] PM: Adding info for No Bus:ram6
[4294667.710000] PM: Adding info for No Bus:1:6
[4294667.715000] PM: Adding info for No Bus:ram7
[4294667.719000] PM: Adding info for No Bus:1:7
[4294667.724000] PM: Adding info for No Bus:ram8
[4294667.728000] PM: Adding info for No Bus:1:8
[4294667.733000] PM: Adding info for No Bus:ram9
[4294667.737000] PM: Adding info for No Bus:1:9
[4294667.742000] PM: Adding info for No Bus:ram10
[4294667.746000] PM: Adding info for No Bus:1:10
[4294667.751000] PM: Adding info for No Bus:ram11
[4294667.755000] PM: Adding info for No Bus:1:11
[4294667.760000] PM: Adding info for No Bus:ram12
[4294667.764000] PM: Adding info for No Bus:1:12
[4294667.769000] PM: Adding info for No Bus:ram13
[4294667.773000] PM: Adding info for No Bus:1:13
[4294667.778000] PM: Adding info for No Bus:ram14
[4294667.782000] PM: Adding info for No Bus:1:14
[4294667.787000] PM: Adding info for No Bus:ram15
[4294667.792000] PM: Adding info for No Bus:1:15
[4294667.796000] brd: module loaded
[4294667.800000] PM: Adding info for No Bus:loop0
[4294667.804000] PM: Adding info for No Bus:7:0
[4294667.809000] PM: Adding info for No Bus:loop1
[4294667.813000] PM: Adding info for No Bus:7:1
[4294667.818000] PM: Adding info for No Bus:loop2
[4294667.822000] PM: Adding info for No Bus:7:2
[4294667.827000] PM: Adding info for No Bus:loop3
[4294667.831000] PM: Adding info for No Bus:7:3
[4294667.836000] PM: Adding info for No Bus:loop4
[4294667.840000] PM: Adding info for No Bus:7:4
[4294667.845000] PM: Adding info for No Bus:loop5
[4294667.849000] PM: Adding info for No Bus:7:5
[4294667.854000] PM: Adding info for No Bus:loop6
[4294667.858000] PM: Adding info for No Bus:7:6
[4294667.863000] PM: Adding info for No Bus:loop7
[4294667.867000] PM: Adding info for No Bus:7:7
[4294667.872000] loop: module loaded
[4294667.875000] PM: Adding info for platform:bcm7038.0
[4294667.880000] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
[4294667.888000] bcmemac: MAC address E8:5B:5B:A1:48:0Dfetched from bootloader
[4294667.895000] Broadcom internal 7038 10/100 Ethernet Network Device
[4294667.903000] Config Internal PHY Through MDIO<6>usbcore: registered new interface driver pegasus
[4294667.913000] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver
[4294667.920000] usbcore: registered new interface driver rtl8150
[4294667.926000] Driver 'sd' needs updating - please use bus_type methods
[4294667.933000] Driver 'sr' needs updating - please use bus_type methods
[4294667.939000] PM: Adding info for platform:vide_ofe
[4294667.945000] scsi0 : vide_ofe
[4294667.948000] PM: Adding info for No Bus:host0
[4294667.953000] PM: Adding info for No Bus:host0
[4294667.957000] ata1: SATA max UDMA/133 ioport cmd 0xb0290000 irq 44
[4294667.963000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 0)
[4294667.973000] ata1.00: ATAPI: LGE     D TREIRLA EE D0RSHN8 A, 0591, max UDMA/33
[4294667.984000] ata1.00: configured for UDMA/33
[4294667.989000] __ata_scsi_queuecmd(3129) : Remove early spinup
[4294667.995000] scsi 0:0:0:0: CD-ROM            LGH08SAN LG H08SAN BC7630 0591 PQ: 0 ANSI: 5
[4294668.003000] ata_scsi_dev_config: prior alignment 0x1ff
[4294668.009000] PM: Adding info for No Bus:target0:0:0
[4294668.014000] PM: Adding info for scsi:0:0:0:0
[4294668.019000] error : drv_stat = 51 (0)
[4294668.024000] sr0: scsi3-mmc drive: 24x/24x caddy
[4294668.028000] Uniform CD-ROM driver Revision: 3.20
[4294668.033000] PM: Adding info for No Bus:sr0
[4294668.038000] PM: Adding info for No Bus:11:0
[4294668.042000] sr 0:0:0:0: Attached scsi CD-ROM sr0
[4294668.047000] PM: Adding info for No Bus:0:0:0:0
[4294668.052000] PM: Adding info for No Bus:sg0
[4294668.056000] sr 0:0:0:0: Attached scsi generic sg0 type 5
[4294668.062000] brcmnand_init enter
[4294668.066000] PM: Adding info for platform:bcm7xxx-nand
[4294668.071000] brcmnand_probe: Calling brcmnand_prescan
[4294668.096000] brcmnand_read_id: CS0: dev_id=98da9015
[4294668.101000] brcmnand_prescan: Writing 0x00000000 in BCHP_NAND_CS_NAND_XOR
[4294668.108000] brcmnand_probe: Calling brcmnand_scan
[4294668.132000] brcmnand_read_id: CS0: dev_id=98da9015
[4294668.137000] brcmnand_probe: Found SLC device TOSHIBA SLC TC58NVG1S3ETA00
[4294668.143000] brcmnand_probe() oobSize: 16,  pageSize : 2048, blockSize: 131072<7>Writing nand config register 0x01402848 with 0x16152300
[4294668.156000] MSK_BLK_SIZE: 70000000, SHT_BLK_SIZE: 0000001C
[4294668.162000] NAND Config: Reg=16152300, chipSize=256MB, blockSize=128K, erase_shift=11
[4294668.170000] busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
[4294668.177000] Adjust timing1: Was 33535233, changed to 33535233
[4294668.183000] Adjust timing2: Was 80000b98, changed to 80000b98
[4294668.188000] BrcmNAND mfg 98 da TOSHIBA SLC TC58NVG1S3ETA00 256MB
[4294668.195000] BrcmNAND mfg 98 da TOSHIBA SLC TC58NVG1S3ETA00 256MB
[4294668.201000] Found NAND: ACC=e3441010, cfg=16152300, flashId=98da9015, tim1=33535233, tim2=80000b98
[4294668.210000] BrcmNAND version = 0x80000304 256MB @00000000
[4294668.236000] brcmnand_read_id: CS0: dev_id=98da9015
[4294668.241000] brcmnand_scan: B4 nand_select = 40000101
[4294668.246000] brcmnand_scan: After nand_select = 40000100
[4294668.251000] Setting ECC to BCH-4: ACC_CONTROL = e3441010 from e3441010
[4294668.258000] Setting BCH4 THRESHOLD to 3
[4294668.262000] brcmnand_scan: mtd->oobsize = 64
[4294668.266000] brcmnand_scan: Setting ecclayout to brcmnand_oob_bch4_2k
[4294668.273000] Disabling PARTIAL_PAGE
[4294668.277000] Enabling PAGE_HIT
[4294668.280000] Enabling WR_PREEMPT
[4294668.283000] ACC_CONTROL for SLC NAND: e3441010
[4294668.288000] page_shift=11, bbt_erase_shift=17, chip_shift=28, phys_erase_shift=17
[4294668.295000] mtd->oobsize = 64,  this->phys_erase_shift = 17, this->page_shift = 11
[4294668.303000] mtd->eccsize=512, eccbytes=7
[4294668.307000] Brcm NAND controller version (EDU Enable) = 3.4 NAND flash size 256MB @00000000
[4294668.316000] Block Scrubbing is Enable
[4294668.320000] Product Revision 0x76300010 <5>brcmnand_scan : This driver does not perform physical to logical maping [XOR with 0x00000000]
[4294668.333000] brcmnand_scan_bbt: Allocating 512 bytes for RAM buffer,
[4294668.339000] brcmnand_scan_bbt: Allocating 2112 bytes flash buffer,
[4294668.346000] brcmnand_search_bbt: actblock=2047, from=0ffe0000, ooblock=2048, oobsize=64
[4294668.354000] Offset in buf for reading version 1: 2054
[4294668.360000] Version is: 1
[4294668.363000] Bad block table found at page 131008, version 0x01
[4294668.369000] brcmnand_search_bbt: actblock=2047, from=0ffe0000, ooblock=2048, oobsize=64
[4294668.377000] brcmnand_search_bbt: actblock=2046, from=0ffc0000, ooblock=2048, oobsize=64
[4294668.385000] Offset in buf for reading version 1: 2054
[4294668.391000] Version is: 1
[4294668.393000] Bad block table found at page 130944, version 0x01
[4294668.400000] - Flash Type: NAND
[4294668.403000] - Number of Flash Partitions: 21
[4294668.407000] nPartitionQty:21, sizeof(struct mtd_partition): 28
[4294668.414000] nandinfo->parts: 826A4400
[4294668.417000] -   Partition 0: Name: flash0.cfe, base 0x00000000, offset 0x00000000, size 0x00100000
[4294668.427000] -   Partition 1: Name: flash0.splash, base 0x00000000, offset 0x00100000, size 0x00600000
[4294668.436000] -   Partition 2: Name: flash0.macadr, base 0x00000000, offset 0x00700000, size 0x00000090
[4294668.445000] -   Partition 3: Name: flash0.nvram, base 0x00000000, offset 0x00700090, size 0x00000770
[4294668.455000] -   Partition 4: Name: flash0.virtual, base 0x00000000, offset 0x00700800, size 0x000ff800
[4294668.464000] -   Partition 5: Name: flash0.bct, base 0x00000000, offset 0x00800000, size 0x00100000
[4294668.473000] -   Partition 6: Name: flash0.dbg, base 0x00000000, offset 0x00900000, size 0x00200000
[4294668.483000] -   Partition 7: Name: flash0.kernel1, base 0x00000000, offset 0x00b00000, size 0x00400000
[4294668.492000] -   Partition 8: Name: flash0.kernel, base 0x00000000, offset 0x00f00000, size 0x00400000
[4294668.502000] -   Partition 9: Name: flash0.rootfs1, base 0x00000000, offset 0x01300000, size 0x06600000
[4294668.511000] -   Partition 10: Name: flash0.rootfs, base 0x00000000, offset 0x07900000, size 0x06600000
[4294668.521000] -   Partition 11: Name: flash0.drmregion, base 0x00000000, offset 0x0df00000, size 0x00100000
[4294668.530000] -   Partition 12: Name: flash0.eeprom, base 0x00000000, offset 0x0e000000, size 0x00100000
[4294668.540000] -   Partition 13: Name: flash0.setup, base 0x00000000, offset 0x0e100000, size 0x01800000
[4294668.549000] -   Partition 14: Name: flash0.ofefw.0, base 0x00000000, offset 0x0f900000, size 0x00200000
[4294668.559000] -   Partition 15: Name: flash0.ofews.0, base 0x00000000, offset 0x0fb00000, size 0x00100000
[4294668.569000] -   Partition 16: Name: flash0.ofefw.1, base 0x00000000, offset 0x0fc00000, size 0x00200000
[4294668.578000] -   Partition 17: Name: flash0.ofews.1, base 0x00000000, offset 0x0fe00000, size 0x00100000
[4294668.588000] -   Partition 18: Name: flash0.bbt, base 0x00000000, offset 0x0ff00000, size 0x00100000
[4294668.597000] -   Partition 19: Name: flash1.config, base 0x00700000, offset 0x00000000, size 0x00100000
[4294668.607000] -   Partition 20: Name: flash2.all, base 0x00000000, offset 0x00000000, size 0x0ff00000
[4294668.616000] brcmnand_setup_mtd_partitions: Configure NAND flash partition map from CFE - [21] partitions reported]
[4294668.626000] Hiding Bad Block Table Partition from /proc/mtd
[4294668.632000] 'all' partition size: 267386880
[4294668.637000] NAND flash partitions total size: 268435456
[4294668.642000] Creating 20 MTD partitions on "bcm7xxx-nand":
[4294668.648000] 0x00000000-0x00100000 : "cfe"
[4294668.652000] PM: Adding info for No Bus:romblock0
[4294668.657000] PM: Adding info for No Bus:253:0
[4294668.662000] PM: Adding info for No Bus:mtdblock0
[4294668.667000] PM: Adding info for No Bus:31:0
[4294668.671000] PM: Adding info for No Bus:mtd0
[4294668.676000] PM: Adding info for No Bus:mtd0ro
[4294668.680000] 0x00100000-0x00700000 : "splash"
[4294668.685000] PM: Adding info for No Bus:romblock1
[4294668.690000] PM: Adding info for No Bus:mtdblock1
[4294668.695000] PM: Adding info for No Bus:mtd1
[4294668.700000] PM: Adding info for No Bus:mtd1ro
[4294668.704000] 0x00700000-0x00700090 : "macadr"
[4294668.709000] mtd: partition "macadr" doesn't end on an erase block -- force read-only
[4294668.717000] PM: Adding info for No Bus:romblock2
[4294668.722000] PM: Adding info for No Bus:mtdblock2
[4294668.727000] PM: Adding info for No Bus:mtd2
[4294668.731000] PM: Adding info for No Bus:mtd2ro
[4294668.736000] 0x00700090-0x00700800 : "nvram"
[4294668.740000] mtd: partition "nvram" doesn't start on an erase block boundary -- force read-only
[4294668.749000] PM: Adding info for No Bus:romblock3
[4294668.754000] PM: Adding info for No Bus:mtdblock3
[4294668.759000] PM: Adding info for No Bus:mtd3
[4294668.764000] PM: Adding info for No Bus:mtd3ro
[4294668.768000] 0x00700800-0x00800000 : "virtual"
[4294668.773000] mtd: partition "virtual" doesn't start on an erase block boundary -- force read-only
[4294668.782000] PM: Adding info for No Bus:romblock4
[4294668.787000] PM: Adding info for No Bus:mtdblock4
[4294668.792000] PM: Adding info for No Bus:mtd4
[4294668.796000] PM: Adding info for No Bus:mtd4ro
[4294668.801000] 0x00800000-0x00900000 : "bct"
[4294668.805000] PM: Adding info for No Bus:romblock5
[4294668.810000] PM: Adding info for No Bus:mtdblock5
[4294668.815000] PM: Adding info for No Bus:mtd5
[4294668.820000] PM: Adding info for No Bus:mtd5ro
[4294668.824000] 0x00900000-0x00b00000 : "dbg"
[4294668.829000] PM: Adding info for No Bus:romblock6
[4294668.834000] PM: Adding info for No Bus:mtdblock6
[4294668.839000] PM: Adding info for No Bus:mtd6
[4294668.843000] PM: Adding info for No Bus:mtd6ro
[4294668.848000] 0x00b00000-0x00f00000 : "kernel1"
[4294668.853000] PM: Adding info for No Bus:romblock7
[4294668.858000] PM: Adding info for No Bus:mtdblock7
[4294668.863000] PM: Adding info for No Bus:mtd7
[4294668.867000] PM: Adding info for No Bus:mtd7ro
[4294668.872000] 0x00f00000-0x01300000 : "kernel"
[4294668.876000] PM: Adding info for No Bus:romblock8
[4294668.881000] PM: Adding info for No Bus:mtdblock8
[4294668.886000] PM: Adding info for No Bus:mtd8
[4294668.891000] PM: Adding info for No Bus:mtd8ro
[4294668.896000] 0x01300000-0x07900000 : "rootfs1"
[4294668.901000] PM: Adding info for No Bus:romblock9
[4294668.906000] PM: Adding info for No Bus:mtdblock9
[4294668.911000] PM: Adding info for No Bus:mtd9
[4294668.915000] PM: Adding info for No Bus:mtd9ro
[4294668.920000] 0x07900000-0x0df00000 : "rootfs"
[4294668.925000] PM: Adding info for No Bus:romblock10
[4294668.930000] PM: Adding info for No Bus:mtdblock10
[4294668.935000] PM: Adding info for No Bus:mtd10
[4294668.940000] PM: Adding info for No Bus:mtd10ro
[4294668.944000] 0x0df00000-0x0e000000 : "drmregion"
[4294668.949000] PM: Adding info for No Bus:romblock11
[4294668.954000] PM: Adding info for No Bus:mtdblock11
[4294668.959000] PM: Adding info for No Bus:mtd11
[4294668.964000] PM: Adding info for No Bus:mtd11ro
[4294668.969000] 0x0e000000-0x0e100000 : "eeprom"
[4294668.973000] PM: Adding info for No Bus:romblock12
[4294668.979000] PM: Adding info for No Bus:mtdblock12
[4294668.984000] PM: Adding info for No Bus:mtd12
[4294668.988000] PM: Adding info for No Bus:mtd12ro
[4294668.993000] 0x0e100000-0x0f900000 : "setup"
[4294668.998000] PM: Adding info for No Bus:romblock13
[4294669.003000] PM: Adding info for No Bus:mtdblock13
[4294669.008000] PM: Adding info for No Bus:mtd13
[4294669.012000] PM: Adding info for No Bus:mtd13ro
[4294669.017000] 0x0f900000-0x0fb00000 : "ofefw.0"
[4294669.022000] PM: Adding info for No Bus:romblock14
[4294669.027000] PM: Adding info for No Bus:mtdblock14
[4294669.032000] PM: Adding info for No Bus:mtd14
[4294669.037000] PM: Adding info for No Bus:mtd14ro
[4294669.041000] 0x0fb00000-0x0fc00000 : "ofews.0"
[4294669.046000] PM: Adding info for No Bus:romblock15
[4294669.051000] PM: Adding info for No Bus:mtdblock15
[4294669.056000] PM: Adding info for No Bus:mtd15
[4294669.061000] PM: Adding info for No Bus:mtd15ro
[4294669.065000] 0x0fc00000-0x0fe00000 : "ofefw.1"
[4294669.070000] PM: Adding info for No Bus:romblock16
[4294669.075000] PM: Adding info for No Bus:mtdblock16
[4294669.080000] PM: Adding info for No Bus:mtd16
[4294669.085000] PM: Adding info for No Bus:mtd16ro
[4294669.090000] 0x0fe00000-0x0ff00000 : "ofews.1"
[4294669.094000] PM: Adding info for No Bus:romblock17
[4294669.099000] PM: Adding info for No Bus:mtdblock17
[4294669.105000] PM: Adding info for No Bus:mtd17
[4294669.109000] PM: Adding info for No Bus:mtd17ro
[4294669.114000] 0x00700000-0x00800000 : "config"
[4294669.119000] PM: Adding info for No Bus:romblock18
[4294669.124000] PM: Adding info for No Bus:mtdblock18
[4294669.129000] PM: Adding info for No Bus:mtd18
[4294669.133000] PM: Adding info for No Bus:mtd18ro
[4294669.138000] 0x00000000-0x0ff00000 : "all"
[4294669.144000] PM: Adding info for No Bus:romblock19
[4294669.149000] PM: Adding info for No Bus:mtdblock19
[4294669.154000] PM: Adding info for No Bus:mtd19
[4294669.158000] PM: Adding info for No Bus:mtd19ro
[4294669.163000] brcmnand_probe: Calling brcmnand_prescan
[4294669.188000] brcmnand_read_id: no multi-nand found 1
[4294669.193000] brcmnand_probe: Device [1] does not exist
[4294669.198000] brcmnand_probe: Calling brcmnand_prescan
[4294669.223000] brcmnand_read_id: no multi-nand found 2
[4294669.228000] brcmnand_probe: Device [2] does not exist
[4294669.233000] brcmnand_probe: Calling brcmnand_prescan
[4294669.258000] brcmnand_read_id: no multi-nand found 3
[4294669.263000] brcmnand_probe: Device [3] does not exist
[4294669.268000] PM: Adding info for No Bus:ubi_ctrl
[4294669.273000] PM: Adding info for No Bus:usbmon0
[4294669.278000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[4294669.284000]  - USB h/w setup mode <N>
[4294669.288000]  - USB power enable set for active LOW mode (val = 0x00000033)
[4294669.295000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
[4294669.301000] PM: Adding info for No Bus:usb_host1
[4294669.306000] PM: Adding info for No Bus:usbmon1
[4294669.311000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
[4294669.350000] ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
[4294669.361000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
[4294669.367000] PM: Adding info for usb:usb1
[4294669.371000] usb usb1: configuration #1 chosen from 1 choice
[4294669.377000] PM: Adding info for usb:1-0:1.0
[4294669.381000] hub 1-0:1.0: USB hub found
[4294669.385000] hub 1-0:1.0: 2 ports detected
[4294669.390000] PM: Adding info for No Bus:usbdev1.1_ep81
[4294669.395000] PM: Adding info for No Bus:usbdev1.1
[4294669.400000] PM: Adding info for No Bus:usbdev1.1_ep00
[4294669.406000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[4294669.412000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
[4294669.417000] PM: Adding info for No Bus:usb_host2
[4294669.422000] PM: Adding info for No Bus:usbmon2
[4294669.427000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 2
[4294669.435000] ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
[4294669.506000] PM: Adding info for usb:usb2
[4294669.510000] usb usb2: configuration #1 chosen from 1 choice
[4294669.516000] PM: Adding info for usb:2-0:1.0
[4294669.520000] hub 2-0:1.0: USB hub found
[4294669.525000] hub 2-0:1.0: 2 ports detected
[4294669.529000] PM: Adding info for No Bus:usbdev2.1_ep81
[4294669.534000] PM: Adding info for No Bus:usbdev2.1
[4294669.539000] PM: Adding info for No Bus:usbdev2.1_ep00
[4294669.545000] Initializing USB Mass Storage driver...
[4294669.550000] usbcore: registered new interface driver usb-storage
[4294669.556000] USB Mass Storage support registered.
[4294669.561000] usbcore: registered new interface driver usbserial
[4294669.567000] usbserial: USB Serial Driver core
[4294669.572000] USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
[4294669.580000] usbcore: registered new interface driver belkin
[4294669.586000] belkin_sa: v1.2:USB Belkin Serial converter driver
[4294669.592000] USB Serial support registered for pl2303
[4294669.598000] usbcore: registered new interface driver pl2303
[4294669.603000] pl2303: Prolific PL2303 USB to serial adaptor driver
[4294669.610000] brcm_crypt_init: SHA-1 HW assist for DigSig
[4294669.615000] Advanced Linux Sound Architecture Driver Version 1.0.18rc3.
[4294669.622000] PM: Adding info for No Bus:timer
[4294669.627000] PM: Adding info for No Bus:sequencer
[4294669.632000] PM: Adding info for No Bus:sequencer2
[4294669.637000] : 100 MB Full-Duplex (auto-neg)
[4294669.642000] PM: Adding info for No Bus:eth0
[4294669.647000] init link_change_task
[4294669.651000] PM: Adding info for No Bus:seq
[4294669.655000] usbcore: registered new interface driver snd-usb-audio
[4294669.662000] ALSA device list:
[4294669.665000]   No soundcards found.
[4294669.669000] TCP cubic registered
[4294669.672000] NET: Registered protocol family 17
[4294669.677000] RPC: Registered udp transport module.
[4294669.682000] RPC: Registered tcp transport module.
[4294669.687000] PM: Adding info for No Bus:cpu_dma_latency
[4294669.693000] PM: Adding info for No Bus:network_latency
[4294669.698000] PM: Adding info for No Bus:network_throughput
[4294669.708000] VFS: Mounted root (squashfs filesystem) readonly.
[4294669.715000] Freeing unused kernel memory: 176k freed
[4294669.721000] PM: Adding info for No Bus:watchdog
[4294669.911000] Algorithmics/MIPS FPU Emulator v1.5
[4294670.177000] yaffs: dev is 32505869 name is "mtdblock13"
[4294670.182000] yaffs: passed flags ""
[4294670.186000] yaffs: Attempting MTD mount on 31.13, "mtdblock13"
[4294670.192000] yaffs_internal_read_super: nBlocks: 192, mtd->size = 25165824, mtd->erasesize = 131072,  WRITE_SIZE(mtd)=2048
[4294670.218000] yaffs: restored from checkpoint
[4294670.222000] yaffs_read_super: isCheckpointed 1
Thu Mar 25 00:00:00 UTC 2010
[4294670.303000] bcmdriver: no version for "struct_module" found: kernel tainted.
[4294670.311000] bcmdriver: module license 'Proprietary' taints kernel.
[4294670.347000] BCMDRV: Initializing bcmdriver version $ bdvd_v3.0/2 $
[4294670.354000] BCMDRV: Using Interrupt Definition for 7630 (uname -a)
[4294670.360000] BCMDRV: Total intc words=2,Total Irqs=65
[4294670.366000] BCMDRV: Global Interrupt Mask 0:0xD09E3FEF,1:0x0EB20003,2:0x00000000,3:0x00000000
[4294670.375000] BCMDRV: Initialization complete...
[4294671.246000] usbcore: registered new interface driver dbus_usbdev
[ NETINIT ] Netinit Ver: 1.0.5.20

./app_ofe_sb: Issue SB_IOCTL_GETCMD
206.269:2D1AA000] Initialize the Console I/O Manager.
206.270:2D1AA000:src/os/core/CONIO_OSA.c:0503:OSA_CONIO_LoadPrintParam] >   2 < Opening failed! [ /mnt/doc0/printparam.dat ]
206.300:2D1AA000] Initialize the Mutex Manager.
206.301:2D1AA000] Initialize the Semaphore Manager.
206.301:2D1AA000] Initialize the Memory Allocation Manager.
206.301:2D1AA000] Initialize the Message Queue Manager.
SIGCONT handler for task resumption is installed and it ignores any previously installed handler.
SIGTSTP handler for task suspension is installed and it ignores any previously installed handler.
206.301:2D1AA000] Initialize the Task Manager.
206.301:2D1AA000] Initialize the Timer Callback Manager.
206.303:LogMgr  ] Start the Log task ...
206.303:2D1AA000] Initialize the Log Manager.
206.319:2D1AA000] Initialize the Board Information.
206.365:2D1AA000] Initialize the Player Option.

Install (signal) backtracer:
  [01] SIGSEGV handler is installed and it ignores any previously installed handler.
  [02] SIGBUS  handler is installed and it ignores any previously installed handler.
  [03] SIGILL  handler is installed and it ignores any previously installed handler.
  [04] SIGFPE  handler is installed and it ignores any previously installed handler.
206.366:2D1AA000] (BOOT-00) ( 0.000) src/main/main.cpp, 98, bdvd_player_lib_main_xyz
206.366:2D1AA000] ====================================================
206.366:2D1AA000] PLAYER ENV
206.366:2D1AA000]   force_libpng=y
206.366:2D1AA000]   no_multi_gfxfeeder=1
206.384:2D1AA000]   no_warn_long_critsect=y
206.385:2D1AA000]   pe_disable_cec=y
206.385:2D1AA000] ====================================================
206.385:2D1AA000] ====================================================
206.385:2D1AA000] PLAYER START
206.385:2D1AA000]   LG_BD_5200B30.ROM, BD.8.31.231.C
206.385:2D1AA000] ====================================================
206.385:2D1AA000] (BOOT-01) ( 0.019) src/main/main.cpp, 181, bdvd_player_lib_main_xyz
206.386:2D1AA000] (BOOT-02) ( 0.020) src/psl/psl_interface.cpp, 223, PslCreate
enabling realtime scheduling
### OS_TaskSpawnParam: thread 'PslTask' stack size is 4194304
206.431:2D1AA000] (BOOT-03) ( 0.064) src/main/main.cpp, 197, bdvd_player_lib_main_xyz
206.431:2D5B0520] (BOOT-04) ( 0.065) src/psl/psl_interface.cpp, 649, PslTask
206.431:2D5B0520] (BOOT-05) ( 0.065) src/psl/psl_interface.cpp, 657, PslTask
### OS_TaskSpawnParam: thread 'USBInfoManager' stack size is 131072
206.432:2D5B0520] (BOOT-06) ( 0.066) src/psl/psl_interface.cpp, 661, PslTask
xxx ok !!
ok !!
206.469:TmrMgr00] Start the  timer (callback task) ...
206.469:2D5B0520] [MICOM] Initialize the MICOM driver.
206.470:TmrMgr01] Start the  timer (callback task) ...
206.470:2D5B0520] [POWER API] Initialize the Power module.
206.470:2D5B0520:src/drv/fp/VFD_CAL.c:0551:CAL_VFD_Initialize] [VFD] Not supported!
206.470:2D5B0520] [VFD API] Initialize the VFD module.
206.470:2D5B0520] [LED] Initialize the led2504ag device.
206.470:2D5B0520] [LED] Initialize the LED driver.
206.471:TmrMgr02] Start the  timer (callback task) ...
206.471:2D5B0520] [LED API] Initialize the LED module.
206.471:2D5B0520] (BOOT-07) ( 0.105) src/psl/psl_interface.cpp, 675, PslTask
### OS_TaskSpawnParam: thread 'LGMiscTask' stack size is 131072
206.472:2D5B0520] (BOOT-08) ( 0.106) src/psl/psl_interface.cpp, 682, PslTask
OSD: OsdInformationInitialize!! start
OSD: OsdSetupLoadConfigSetting!!
OSD: OsdSetupLoadConfigSetting!!
OSD: OsdSetupLoadConfigSetting (setupconfig.inf) success!!
OSD: OsdSetupLoadConfigSetting (setupconfig.inf) success!!
OsdFbSearchHistoryLoad ::: Fail!! This is the non-HDD model!!
****************************************************
*                SETUP INFORMATION
*
* SetTVAspect : TVASPECT_16X9_NORMAL
* Resolution : RE_MANUAL
* Resolution : RE_1080i
* FilmMode : 1
* ColorSpace : 0
* ResolutionMode : 1
* DisplayMenu : ENGLISH
* DiscMenu : Original(1)
* DiscAudio : Original(1)
* DiscSubtitle : OFF(0)
* DivxCharacterSet : CHARACTER_SET_CP1252
* HDMI : 0
* SPDIF : 0
* SampleFreq : FREQ_48KHz
* DRC : TRUE
* bPWSetting : false
* Password : 0
* DiscRating : 0
* BDAge : 255
* AreaCode : DE
* IPSettingMode : DYNAMICIP
* iJavaFontSize : 32
****************************************************
OSD: OsdSetupGetDiscMenu : 1  !!
OSD: OsdSetupGetDiscAudio : 1  !!
OSD: OsdSetupGetDiscSubtitle : 0  !!
OSD: OsdSetupGetResolutionMode : 1  !!
OSD: OsdSetupGetResolution : 3  !!
OSD: OsdSetupGetColorSpace : 0  !!
left.speaker_size = 2
right.speaker_size = 2
center.speaker_size = 2
left_surround.speaker_size = 2
right_surround.speaker_size = 2
LFE.speaker_size = 2
left_back.speaker_size = 2
right_back.speaker_size = 2
left.speaker_volume = 100
right.speaker_volume = 100
center.speaker_volume = 100
left_surround.speaker_volume = 100
right_surround.speaker_volume = 100
LFE.speaker_volume = 100
left_back.speaker_volume = 100
right_back.speaker_volume = 100
PslGetAreaIndex(0x4445)  =DE
OsdSetupGetBDAge() 255
=============================
PslDataLoadConfigSettings successfully
dvd_menu_language        = 16
audio_language           = 16
subtitle_language        = 0
osd_language             = 0
tv_type                  = 0
tv_aspect                = 3
resolution               = 7
resolution_mode       = 1
film_mode                = 0
digital_audio_mode_hdmi  = 4
digital_audio_mode_spdif = 4
dynamic_range_control    = 2
pcm_downsample_hdmi      = 0
pcm_downsample_spdif     = 0
reencode_audio           = 1
dialog_normalization     = 255
crossover_frequency      = 0
parental_country         = 19
parental_level           = 0
parental_on_off          = 1
=============================
206.520:2D5B0520] (BOOT-09) ( 0.154) src/psl/psl_interface.cpp, 697, PslTask
206.520:2D5B0520] (BOOT-10) ( 0.154) src/psl/psl_external_interface.cpp, 274, PslExternalInitialize
206.565:2D5B0520] (BOOT-11) ( 0.198) src/psl/psl_external_interface.cpp, 304, PslExternalInitialize
===============================
src/core/metanav/metanav.cpp::Initialize() -- ENTER
===============================
206.565:2D5B0520] (BOOT-12) ( 0.199) src/core/metanav/metanav.cpp, 641, Initialize
206.565:2D5B0520] (BOOT-13) ( 0.199) src/core/metanav/metanav.cpp, 657, Initialize
umount: Couldn't umount /mnt/captured: Invalid argument

Powered by Gracenote
==================================================
### OS_TaskSpawnParam: thread 'GnMgtTask' stack size is 4194304
### OS_TaskSpawnParam: thread 'GnMsgCtrlTask' stack size is 131072
207.287:2D5B0520] (BOOT-14) ( 0.920) src/core/metanav/metanav.cpp, 681, Initialize
[4294677.573000] error : drv_stat = 51 (0)
[4294677.577000] error : drv_stat = 51 (0)
[4294677.582000] error : drv_stat = 51 (0)
[4294677.586000] error : drv_stat = 51 (0)
[4294677.591000] error : drv_stat = 51 (0)
[4294677.595000] error : drv_stat = 51 (0)
### LoaderCreate() - Boot Option r10_ok not specified

207.367:2D5B0520] (BOOT-15) ( 1.000) src/core/metanav/metanav.cpp, 702, Initialize
207.367:2D5B0520] (BOOT-16) ( 1.001) src/core/metanav/metanav.cpp, 720, Initialize
=== PECreate ===
- bdvd_init
Not enabling warning of CritSect held for too long

 Heaps created
Heap XPT Handle 0x0140e828, PA 0x02800000/ 40M, Size 0x00600000/  6M BW 0
Heap VDC Handle 0x0140ed48, PA 0x02e00000/ 46M, Size 0x01800000/ 24M BW 1
Heap CTX Handle 0x0140f268, PA 0x04600000/ 70M, Size 0x00b80000/ 11M BW 0
Heap XVD Handle 0x0140f788, PA 0x05180000/ 81M, Size 0x02600000/ 38M BW 0
Heap PBK Handle 0x0140fca8, PA 0x07780000/119M, Size 0x00600000/  6M BW 0
Heap RAP Handle 0x014101e8, PA 0x23900000/569M, Size 0x00800000/  8M BW 0
Heap GPI Handle 0x01410728, PA 0x24100000/577M, Size 0x00980000/  9M BW 0
Heap GFX Handle 0x01410c68, PA 0x24a80000/586M, Size 0x0a500000/165M BW 0
Heap PIC Handle 0x014111a8, PA 0x04600000/ 70M, Size 0x03780000/ 55M BW 1### Null image pointer!!!
###
Error in Opening the Image Interface for FW_ID =129

### Null image pointer!!!
###
Error in Opening the Image Interface for FW_ID =129

### bdvd_audio_output_open_sound failed -- audio_output_settings.state != bdvd_audio_output_state_open

### set_drm - Error opening 'N/A/tmp_drm.bin'
### bdvd_drm_key_region_init - Error copying DRM binary data to DRM region (drmregion)
### set_drm - Error opening 'N/A/tmp_drm.bin'
### bdvd_drm_key_region_init - Error copying DRM binary data to DRM Redundant region (drmregion.1)
### OS_TaskSpawnParam: thread 'VCTimerThread00' stack size is 32768
### OS_TaskSpawnParam: thread 'VCTimerThread01' stack size is 32768
### OS_TaskSpawnParam: Could not set thread 'WecEventTask' stack size to 4096 (min is 16384); using 8388608 instead!
- bdvd_init end
PECreate: initialFormat is 10, disp0.format is 10

       ---------------------- DirectFB v0.9.22 ---------------------
             (c) 2000-2002  convergence integrated media GmbH
             (c) 2002-2004  convergence GmbH
        -----------------------------------------------------------

(*) DirectFB/Core: Single Application Core. (2010-04-15 23:54)
(*) DirectFB/BCMCore/system_p_init: video memory size is 173014940
(*) DirectFB/BCMCore/system_p_init: using cached memory for surfaces, cache flush is required
bdvd_graphics: Doing HD full resolution graphics planes
(*) DirectFB/BCMCore/system_p_init: display is set to video_format 10
bdvd_graphics: Using Anisotropic filtering
(*) DirectFB/BCMCore/system_p_init: using mixer compositor for flip-blit
(*) DirectFB/BCMCore/system_p_init: Flip with do a forcefull DSFLIP_WAITFORSYNC
(*) DirectFB/BCMCore/system_p_init: using compositor M2MC for both mixer and driver
(!) Direct/Modules: Could not open module directory `/usr/local/lib/directfb-0.9.22/inputdrivers'!
    --> No such file or directory
(*) DirectFB/BCMGfx/driver_init_driver: driver compositor area threshold is 0
(*) DirectFB/BCMGfx/driver_init_driver: surface memory will not be cleared
(*) DirectFB/Graphics: Broadcom Corporation BCM7438/xxxAPI 0.1 (Broadcom Corporation)
(*) VideoRamSize = 173014940
(*) DirectFB/BCMCore/BCMCoreInitLayer: output layer buffer mode is triple
(*) DirectFB/Core/WM: Default 0.2 (Convergence GmbH)
 (!!!)  *** UNIMPLEMENTED [fusion_reactor_set_lock] *** [reactor.c:802]
=== PECreate End ===
209.005:2D5B0520] (BOOT-17) ( 2.639) src/core/metanav/metanav.cpp, 765, Initialize
209.005:2D5B0520] (BOOT-18) ( 2.639) src/core/metanav/metanav.cpp, 830, Initialize
### OS_TaskSpawnParam: thread 'NetEnvCtrl' stack size is 524288
### OS_TaskSpawnParam: thread 'MetaDiscTask' stack size is 262144
=============================
cMetaNav::DiscTask() -- ENTER
=============================
### OS_TaskSpawnParam: thread 'MetaSimpleCmdTask' stack size is 262144
cMetaNav::SimpleCmdTask() -- ENTER
### OS_TaskSpawnParam: thread 'MetaMP3EncoderTask' stack size is 262144
### OS_TaskSpawnParam: thread 'MetaBackgoundUpdateTask' stack size is 262144
209.009:2D5B0520] (BOOT-19) ( 2.643) src/core/metanav/metanav.cpp, 838, Initialize
209.011:2D5B0520] (BOOT-20) ( 2.644) src/core/metanav/metanav.cpp, 870, Initialize
209.011:2D5B0520] (BOOT-21) ( 2.645) src/core/metanav/metanav.cpp, 881, Initialize
209.011:2D5B0520] (BOOT-22) ( 2.645) src/core/metanav/metanav.cpp, 888, Initialize
LGBackgroundUpdateTask] Enter
[LoaderLGSetDeviceType - 1343] , LoaderDeviceType; 0, LoaderUpdateFileName; H08SAN.BIN
209.014:5681F520] [POWER API]
209.014:5681F520] [POWER API] #####################################
209.014:5681F520] [POWER API] Start this system ...
209.014:5681F520] [POWER API] #####################################
209.014:5681F520] [POWER API]
### OS_TaskSpawnParam: thread 'VCTimerThread02' stack size is 32768
CEC Processing is disabled because pe_disable_cec=y
### OS_TaskSpawnParam: thread 'PEiConfigDisplayTask' stack size is 32768
### hTimer is NULL!
[HDMI CEC] HDMI CABLE OUT ...
[HDMI CEC] HDMI CEC PHYSICAL ADDRESS - REMOVE EVENT
### OS_TaskSpawnParam: thread 'PEiConfigAudioOutputActionProcessingTask' stack size is 32768
209.041:2D5B0520] (BOOT-23) ( 2.675) src/core/metanav/metanav.cpp, 910, Initialize
### OS_TaskSpawnParam: thread 'PEDecEvnt' stack size is 32768
### OS_TaskSpawnParam: thread 'PECmds' stack size is 32768
### OS_TaskSpawnParam: thread 'AudioCaptureTask' stack size is 131072
### OS_TaskSpawnParam: thread 'AudioRecognitionTask' stack size is 131072
209.046:2D5B0520] (BOOT-24) ( 2.679) src/core/metanav/metanav.cpp, 932, Initialize
SetVideoFiltering: Enter
PEiConfigureSetVideoFiltering: Enter!
PEiConfigureSetVideoFiltering: Enter!
JCY : DRC ON ...........!!!!!!!!!!!!!!!!!!!!!!!!!
Initialize:947]4, 4, 0, 0]
SetDigitalAudioOutputHDMI(4): media format = ffffffff
SetDigitalAudioOutputHDMI] mode = 3
SetDigitalAudioOutputSPDIF(4): media format = ffffffff
SetDigitalAudioOutputSPDIF] mode = 3
### bdvd_p_rap_configure_multich_output: i2s_base_port=12, i2s_output_mode=3
### bdvd_p_rap_configure_multich_output: i2s_base_port=2, i2s_output_mode=6
DiscTask-API_POWER_SetState() - Instant Open Mode Out!
#####################################
JCY : print output format information
peiConfigHDMIAudioChange: call set_hdmi_audio (hdmi_aud_path=1, bdvd_aud_out_mode=3, bdvd_aud_fmt=0, rate=48000, chans=2, bits_per_sample=16, channel_config=0)
#####################################

cMetaNav::GetPlayRate -- MEDIA_FORMAT_UNKNOWN, so return 0
cMetaNav::GetPlayRate -- MEDIA_FORMAT_UNKNOWN, so return 0
cMetaNav::SetAudioNeo6Mode() mode=0
209.057:2D5B0520] (BOOT-25) ( 2.691) src/core/metanav/metanav.cpp, 961, Initialize
### bdvd_p_rap_configure_multich_output: i2s_base_port=12, i2s_output_mode=3
### bdvd_p_rap_configure_multich_output: i2s_base_port=2, i2s_output_mode=6
#####################################
JCY : print output format information
peiConfigHDMIAudioChange: call set_hdmi_audio (hdmi_aud_path=1, bdvd_aud_out_mode=3, bdvd_aud_fmt=0, rate=48000, chans=2, bits_per_sample=16, channel_config=0)
#####################################

cMetaNav::GetPlayRate -- MEDIA_FORMAT_UNKNOWN, so return 0
cMetaNav::GetPlayRate -- MEDIA_FORMAT_UNKNOWN, so return 0
peiConfigAdjustVideoOutputProc: Return early to PEiConfigureSetVideoPlaneVisible because no change in VideoSettings
cMetaNav::FindMediaFormats() -- STANDBY
209.069:2D5B0520] (BOOT-26) ( 2.702) src/psl/psl_external_interface.cpp, 311, PslExternalInitialize
Metanav::SetAspectRatio VDVD_ASPECT_RATIO_16X9
PE Display (STANDBY) : DISP0 = 1080i50 [ ],  DISP1 = 576i [ ],  SRC = VIDEO_FORMAT_1080P_23_976_PAL
HL Loader firmware version : H80591

 LLoaderLGGetUpdateFileName : H08SAN.BIN

 H08 Series Emergency Update : /mnt/doc1/loader/H08SAN.BIN !
 Loader FW version is valid
############# ConfirmLGUpdateAndWait ##############
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x00000000 and ending at 0x00100000...
read BCT] EXIT
=============Check CRC32 of Boot Config Table ==============
Written CRC Value:
LONG:   2278711840
HEX:    0x87d26220
Generated CRC Value:
LONG:   2278711840
HEX:    0x87d26220
 ==> CRC OK.
=============== Boot Config Table (/dev/mtd5) ============================================================================

APP_DEV=0x00
ROOTFS_DEV=0x0a
KERNEL_DEV=0x08
LOADER_DEV=0x01
IS_NEW_APP=0x00
IS_NEW_ROOTFS=0x00
IS_NEW_KERNEL=0x00
IS_NEW_LOADER[4294679.695000] error : drv_stat = 51 (0)
=0x00
DID_RESTORE=0x00
TRY_COUNT=0x00
TRY_THRESHOLD=0x03
RESERVED3=0xff
BCT Version=[0xff][0xff][0xff][0xff]
CURRENT_STARTUP=splash -576p; boot -z -elf flash0.kernel: 'root=/dev/romblock10 ro rootfstype=squashfs videotype=PAL memcfg=384 OFE_SB=y quiet console=0,115200n8'[0x00]
PREVIOUS_STARTUP=splash -576p; boot -z -elf flash0.kernel1: 'root=/dev/romblock9 ro rootfstype=squashfs videotype=PAL memcfg=384 OFE_SB=y quiet console=0,115200n8'[0x00]
CRC=0x 20 62 d2 87

Normal boot
Normal boot
 d2 87
lash -576p; boot -z -elf flash0.kernel1: 'root=/dev/romblock9 ro rootfstype=squasRESULT] Normal boot
cMetaNav::SetfUserConfirmUpdateFailure] set m_fUserConfirmUpdateFailure from 0 to 0
cMetaNav::ConfirmLGUpdate] !!!!Normal, EXIT !!!!!
Already Notified
cMetaNav::NotifyNewUpdateAndWait] !!!!Normal, EXIT !!!!!
cMetaNav::EnableBackgroundUpdate] 0 -> 1
cMetaNav::SetBackgroundUpdate] 0 -> 1
UsrEventHandler: 18
209.461:5681F520] [  21] <<Status>> (1) [Loading]
<CSA>cMetaNav::DiscTask(11347) -- VDVD_STATUS_LOADING, power_key_in (0)
peiConfigPlayPCM @ 2565: ENTER
*** ERROR (line: 2580): open failed
ChangeVideoOutput : SetVideoFormat(198[4294679.801000] error : drv_stat = 51 (0)
4)
VideoFormat = 7
bt : ChangeVideoOutput(5981)
PEiConfigureGetSubPicState: Unable to get status from the SPU!
*****************************************************
PEiConfigureSetVideoOutput is called at cMetaNav::ChangeVideoOutput
bt : ChangeVideoOutput(6004)
ilongilong PAL Mode
PE Display: DISP0 = 1080i50 [ CMPNT ],  DISP1 = 576i [ CMPST ],  SRC = VIDEO_FORMAT_1080P_23_976_PAL
peiConfigAdjustVideoOutputProc -- RESUME bdvd_display
====================================
cMetaNav::DiscTask() -- Loader Ready
====================================
 LoaderLGIsDiscBlank() -- NoDisc
MountDvdromDrive : DVD-ROM Disc or Not DVD Disc !!!
IsDataTrackExist : Not CD Disc !!!
cMetaNav::DiscTask() -- MEDIA_FORMAT_NODISC
cMetaNav::DiscTask() -- LOADER READY
cMetaNav::DetectMediaType()
cDiskInfo::readDiskInfo() -- LoaderGetMediaData
cDiskInfo::detectMediaFormat() -- MEDIA_FORMAT_NODISC
cDiskInfo::readDiskInfo()--Media format 0x00000000
cMetaNav::DetectMediaType() -- MEDIA_FORMAT_NODISC
cMetaNav::EnableBackgroundUpdate] 1 -> 1
cMetaNav::SetBackgroundUpdate] 1 -> 1
UsrEventHandler: 16
209.573:5681F520] [  19] <<Status>> (1) [No Disc]
detect:1928
ilongilong Refresh Splash Screen by Changing DirectFB
UsrEventHandler: 125
209.822:2D5B0520] [ 115] <<Status>> (1) [RefreshGraphics]
bt : ChangeVideoOutput(6015)
209.844:2D5B0520] (BOOT-27) ( 3.478) src/psl/psl_external_interface.cpp, 326, PslExternalInitialize
osd_init
osd_init start
osd_init:1
osd_init:2
osd_init:3
osd_init:4
osd_init:5
osd_init:6
osd_init:7
osd_init:8
osd_init:9
osd_init:first_obj MemAlloc
osd_init end
209.976:2D5B0520] (BOOT-28) ( 3.610) src/psl/psl_external_interface.cpp, 341, PslExternalInitialize
209.977:2D5B0520] PslProcessUserInputPower(): ENTER (1)
209.977:2D5B0520] PslProcessUserInputPower(): <PSL_USER_CMD_POWER (1) >
PslExternalSendNavCommand: (0)
src/core/metanav/metanav.cpp::SendLocalCommand() -- Entering with Message Type 2
cMetaNav::SendLocalCommand() -- SENDING SIMPLECMD_REMOTE_MSG
src/core/metanav/metanav.cpp::SimpleCmdTask() -- SIMPLECMD_REMOTE_MSG
cMetaNav::ProcessCommands -- VDVD_COMMAND_STANDBY
cMetaNav::ProcessCommands -- Come out of standby mode
UsrEventHandler: 59
209.977:5685F520] [  40] <<Status>> (1) [Splash Screen]
UsrEventHandler: 29
209.977:5685F520] [  27] <<Status>> (1) [Standby]
src/core/metanav/metanav.cpp::ProcessCommands() Leaving
DiscTask(11032)
cMetaNav::DiscTask() -- DISCMSG_TRAY_STATUS
cMetaNav::SendLocalCommand() -- SUCCESS
PslExternalSendNavCommand: (0) END
209.978:2D5B0520] PslProcessUserInputPower(): EXIT (1)
PslExternalInitialize: Create OSD
209.978:2D5B0520] (BOOT-29) ( 3.612) src/psl/psl_external_interface.cpp, 349, PslExternalInitialize


***************************************************
OSD_CREATE : filename =/usr/local/share/turnkey/osd_smb2_us_en.xml
language=en, playerModel = 13, osdLang 0
***************************************************
osd_create start
osd_wmenu_create: ENTER
osd_wmenu_create: LG_HOME
osd_wmenu_create: END
OSD : osd_surface_create(0) w=1280,  h=720
OSD : osd_surface_create(1) w=1280,  h=720
osd_create end
210.314:2D5B0520] (BOOT-30) ( 3.947) src/psl/psl_external_interface.cpp, 367, PslExternalInitialize
PslProcessStatusSplashScreen: splashscreen_id = 0x1, ulData2=0
PslProcessStatusSplashScreen: OSD Show SplashScreen
(*) Direct/Interface: Loaded 'PNG' implementation of 'IDirectFBImageProvider'.
(*) force_libpng is set, using libPNG for decode...
### OS_TaskSpawnParam: thread 'MyMediaServerMgrTask' stack size is 262144

********************************************************************
CMyServerList

********************************************************************
My Media Error Getting Last Position File
My Media root already exit
** My Media Error: Getting Saved Passwd File
My Media root already exit
210.904:2D5B0520] (BOOT-31) ( 4.537) src/psl/psl_interface.cpp, 712, PslTask
### OS_TaskSpawnParam: thread 'VCTimerThread03' stack size is 32768
210.905:2D5B0520] (BOOT-32) ( 4.539) src/psl/psl_interface.cpp, 727, PslTask
210.906:TmrMgr03] Start the  timer (callback task) ...
210.906:TmrMgr04] Start the  timer (callback task) ...
210.907:EtherMnt] Start the Ethernet Monitor task ...
210.908:EtherMnt] [ 100] <<Status>> (1) [Network Cable HotPlug]
210.909:TmrMgr05] Start the  timer (callback task) ...
210.910:ScrnSave] Start the Screen Saver Monitor task ...
210.910:TmrMgr06] Start the  timer (callback task) ...
210.911:2D5B0520] Initialize the Miscellaneous interface.

##[KYLEE] MyServerMainTask, 369


!!!!!!!!!!!!!!!MyServerMainTask -- Receive 0

[ILONG][DEBUG][ src/osd/osdInformation.c:7557:OsdSetupStoreConfigSettings ]
OSD: OsdSetupStoreConfigSettings!!
210.955:2D5B0520] (BOOT-33) ( 4.588) src/psl/psl_interface.cpp, 738, PslTask
210.955:2D5B0520] [KEYRCV] Initialize the Key Receiver driver.
210.955:2D5B0520] [UTIL API] Initialize the Utilities module.
210.955:2D5B0520] [UTIL API] Register the Key Receiver callback.
210.955:2D5B0520] (BOOT-34) ( 4.589) src/psl/psl_interface.cpp, 744, PslTask
210.956:2D5B0520] [SWU API] Initialize the Software Update module.
210.956:2D5B0520] [FACINIT API] Initialize the Factory Initialization module.
210.956:2D5B0520] [FACTEST API] Initialize the Factory Test module.
210.956:2D5B0520] Initialize the Hidden Mode interface.
210.956:2D5B0520] (BOOT-35) ( 4.590) src/psl/psl_interface.cpp, 768, PslTask
210.956:KeyRecei] [KEYRCV] Start the Key Receiver task ...
210.991:2D5B0520] [SIMPLINK] <CEC SIGNAL LAYER> Logical Address  : 0x04
210.991:2D5B0520] [SIMPLINK] <CEC SIGNAL LAYER> TV Manufacturer  : --
211.012:TmrMgr07] Start the  timer (callback task) ...
211.013:2D5B0520] [SIMPLINK] Initialize the SIMPLINK driver.
211.013:2D5B0520] [SIMPLINK API] Initialize the SIMPLINK module.
211.013:2D5B0520] [SIMPLINK API] Register the status callback.
211.013:TmrMgr08] Start the  timer (callback task) ...
211.014:2D5B0520] Initialize the CEC interface.
211.014:2D5B0520] (BOOT-36) ( 4.648) src/psl/psl_interface.cpp, 772, PslTask
211.014:2D5B0520] [DBGM API] Initialize the Debug Message module.
211.015:2D5B0520] Initialize the Debug interface.
211.015:2D5B0520] (BOOT-37) ( 4.649) src/psl/psl_interface.cpp, 778, PslTask
PslProcessStatusLoading:(0) ENTER!
PslProcessStatusLoading:(0) 3215
PslProcessStatusSplashScreen: splashscreen_id = 0x1, ulData2=0
211.017:SYSINIT ] [SIMPLINK] Start the System Initiator task ...
211.017:KEYRECEI] [SIMPLINK] Start the Key Receiver task ...
211.017:DebugMnt] Start the Debug Monitor task ...
211.018:NetRmt  ] Start the Network Remote task ...
PslThreadDiscLoading: ENTER
pslthead2 join end (2401)
211.052:2D5B0520] (BOOT-38) ( 4.685) src/psl/psl_process_status.cpp, 2432, PslProcessStatusNoDisc
211.052:2D5B0520] (BOOT-39) ( 4.686) src/psl/psl_process_status.cpp, 2447, PslProcessStatusNoDisc
211.052:2D5B0520] (BOOT-40) ( 4.686) src/psl/psl_process_status.cpp, 2478, PslProcessStatusNoDisc
wmenu_show: ENTER++++++
~~~~~~~~~~~~~~~~~~HOME~~~~~~~~~~~~~~~~~~1
OSD : osd_surface_create(2) w=1280,  h=720
(*) Direct/Interface: Loaded 'FT2' implementation of 'IDirectFBFont'.
osd_lib_CreateThread: ENTER!!
osd_lib_CreateThread: start
wmenu_show: END++++++
211.343:2D5B0520] (BOOT-41) ( 4.976) src/psl/psl_process_status.cpp, 2488, PslProcessStatusNoDisc
OVerlay ::: Action draw !!!!!
PslExternalGetIsActiveUSB -- USB Enable : 0
PslExternalGetIsActiveInternalHDD --Option False  HDD Disable
PslExternalGetIsActiveIPOD -- IPOD Enable : 0
PslExternalGetIsActiveIPODMovie -- IPOD Enable : 0
cMetaNav::GetNewNetworkUpdateImageExistence()] return 2
PslProcessStatusSplashScreen: splashscreen_id = 0x1, ulData2=0
211.383:2D5B0520] PslProcessStatusStandby(): ENTER (1)
OVerlay ::: Action draw !!!!!
HOME_MOVIE_DISC_DIVX ::: FALSE
HOME_MOVIE_USB_DIVX ::: FALSE
HOME_MOVIE_HDD_DIVX ::: FALSE
OSD : OsdSetupGetFileBrowserHddMusicMode ==OSD_FB_MEDIA_MUSIC_LIBRARY !!!!!!!!!!
211.422:2D5B0520] PslProcessStatusStandby(): EXIT (1)
[ NETINIT ] Message Received : cmd = 1
[ NETINIT ] DYNAMIC CMD:rm -rf /tmp/dhcpcd/config/dhcpcd-eth0*; ifconfig eth0 0.0.0.0 netmask 0.0.0.0
SIOCSIFNETMASK: Cannot assign requested address
[ NETINIT ] Chield Process wait SUCCESS : PID[-1]
[ NETINIT ] setDynamicIP: START===
[ NETINIT ] setDynamicIP():: unlink error
[ NETINIT ] Child: DHCPCD Starting(PID:140).
[ NETINIT ] strPIDPath : /tmp/dhcpcd/config/dhcpcd-eth0.info
LG Modified Client
dhcpcd: MAC address = e8:5b:5b:a1:48:0d
Mar 25 00:00:12 dhcpcd[140]: broadcasting DHCP_DISCOVER

Mar 25 00:00:12 dhcpcd[140]: broadcastAddr option is missing in DHCP server response. Assuming 192.168.1.255

Mar 25 00:00:12 dhcpcd[140]: dhcpIPaddrLeaseTime=31536000 in DHCP server response.

Mar 25 00:00:12 dhcpcd[140]: dhcpT1value is missing in DHCP server response. Assuming 15768000 sec

Mar 25 00:00:12 dhcpcd[140]: dhcpT2value is missing in DHCP server response. Assuming 27594000 sec

Mar 25 00:00:12 dhcpcd[140]: DHCP_OFFER received from  (192.168.1.254)

Mar 25 00:00:12 dhcpcd[140]: broadcasting DHCP_REQUEST for 192.168.1.200

Mar 25 00:00:12 dhcpcd[140]: dhcpIPaddrLeaseTime=31536000 in DHCP server response.

Mar 25 00:00:12 dhcpcd[140]: dhcpT1value is missing in DHCP server response. Assuming 15768000 sec

Mar 25 00:00:12 dhcpcd[140]: dhcpT2value is missing in DHCP server response. Assuming 27594000 sec

Mar 25 00:00:12 dhcpcd[140]: DHCP_ACK received from  (192.168.1.254)

dhcpcd: your IP address = 192.168.1.200
[ NETINIT ] Chield Process wait SUCCESS : PID[140]
[ NETINIT ] Received network info from DHCP Server.
[ NETINIT ] Send retValue for NETINIT_CMD_SET_DYNAMIC_IP:OK
send_ret_dhcpcd_result ret:0
NECM>>[1653] NECM_CMD_SET_DYNAMIC_IP : DHCP Client Loaded!!
UsrEventHandler: 124
212.507:567DF520] [ 141] <<Status>> (1) [WIREDNET]


!!!!!!!!!!!!!!!MyServerMainTask -- Receive 1

Stop DLNA
dlna not started
Error Stop Dlna
PslProcessStatusWIREDNET: PslProcessStatusWIREDNET = 0x15, ulData2=1
ggang1 : VDVD_WIREDNET_GET_DYNAMIC_IP_SUCCESS_ID
214.014:Simplink] Start the SIMPLINK Application task ...
214.014:Simplink] [SIMPLINK API] << DIRECT PLAY >>
214.286:Simplink] [SIMPLINK API] < DECK STATUS (32) >
217.862:5A35A520] [  48] <<Status>> (1) [Redraw GUI]


221.043:KeyRecei] [  69] <<Input!>> (1) [Power Off(FP)]  
POWER ON/OFF KEY PRESSED
Home (69)
221.044:2D5B0520] PslProcessUserInputPower(): ENTER (0)
221.044:2D5B0520] PslProcessUserInputPower(): Be ready to POWER OFF ...
221.044:2D5B0520] [POWER API]
221.044:2D5B0520] [POWER API] #####################################
221.044:2D5B0520] [POWER API] Be ready to stop this system ...
221.044:2D5B0520] [POWER API] #####################################
221.044:2D5B0520] [POWER API]
221.085:2D5B0520] PslProcessUserInputPower(): Stop KEY service ...
221.085:2D5B0520] PslProcessUserInputPower(): Stop CEC service ...
221.086:2D5B0520] PslProcessUserInputPower(): Store search history (OSD) ...
OsdFbSearchHistoryStore ::: Fail!! This is the non-HDD model!!
221.086:2D5B0520] PslProcessUserInputPower(): Cancel CD ripping ...
223.087:2D5B0520] PslProcessUserInputPower(): <PSL_USER_CMD_POWER (0) >
PslExternalSendNavCommand: (0)
src/core/metanav/metanav.cpp::SendLocalCommand() -- Entering with Message Type 2
cMetaNav::SendLocalCommand() -- SENDING SIMPLECMD_REMOTE_MSG
src/core/metanav/metanav.cpp::SimpleCmdTask() -- SIMPLECMD_REMOTE_MSG
cMetaNav::ProcessCommands -- VDVD_COMMAND_STANDBY
cMetaNav::ProcessCommands -- Go into standby mode
DiscTask(11032)
cMetaNav::DiscTask() -- DISCMSG_TRAY_STATUS
cMetaNav::SendLocalCommand() -- SUCCESS
PslExternalSendNavCommand: (0) END
223.087:2D5B0520] PslProcessUserInputPower(): EXIT (0)
*****************************************************
PEiConfigureSetVideoOutput is called at cMetaNav::ProcessCommands  2
ProcessCommands : WMDelete
StopDeviceScan:187
StopDeviceScan:190
StopDeviceScan:202
PslExternalGetIsActiveUSB -- USB Enable : 0
### OS_SemTakeTrack: BAD POINTER.

### OS_SemGive: BAD POINTER.

UsrEventHandler: 28
223.089:5685F520] [  27] <<Status>> (1) [Standby]
src/core/metanav/metanav.cpp::ProcessCommands() Leaving
223.090:2D5B0520] PslProcessStatusStandby(): ENTER (0)
OVerlay ::: Action draw !!!!!
223.103:2D5B0520] PslProcessStatusStandby(): Clear all OSDs ...
wmenu_show: ENTER++++++
osd_lib_DeleteThread: ENTER!!
END !!!!!! 1
END !!!!!!2
osd_wmenu_main :END !!!
osd_lib_DeleteThread: join end
OSD: osd_font_destroy() : OK !!
OSD: osd_font_destroy() : OK !!
OSD: osd_font_destroy() : OK !!
OSD: osd_font_destroy() : OK !!
OSD : osd_surface_destroy (2) : OK !!
wmenu_show: END++++++
223.297:2D5B0520] PslProcessStatusStandby(): Give some delay ...
228.297:2D5B0520] PslProcessStatusStandby(): Block all videos ...
SetVideoMute: ON
228.304:2D5B0520] PslProcessStatusStandby(): Set POWER OFF ...
228.304:2D5B0520] [POWER API]
228.304:2D5B0520] [POWER API] #####################################
228.304:2D5B0520] [POWER API] Shut down this system ...
228.304:2D5B0520] [POWER API] #####################################
228.304:2D5B0520] 4294698.571000] save exit: isCheckpointed 1
m[POWER API] 4294698.576000] save exit: isCheckpointed 1
m
umount: none busy - remounted read-only
umount: none busy - remounted read-only
app_player_poweroff -- power off
 

END
 

HOME