Flathead Specifications

Late 90-125hp V8: 1949 to 1953

The Strato-Star EAB V8 for 1953
(shown above)

Major changes occurred to the mid size flathead V8 in 1948 for the new Ford trucks and in 1949 for new Ford and Mercury cars. The new engine incorporated several changes, some obvious and some not. The heads are now bolted to the blocks with 24 bolts (rather than studs and nuts) and the water outlet fittings are moved up to the front corner of the head (rather than the middle of the head). Another major change was the use of the new "Load-A-Matic" distributor, which was driven off the front of the engine, but through a shaft mounted vertically at right angle to the axis of the engine. With this new engine, Ford stopped casting the bell housing integral to the cylinder block, and provided it as a separate component which was bolted on. Internal changes include using a straight stem valve with one-piece valve guide. The belts and pulleys for 1948/49 stayed with the 5/8" wide of previous years, but changed from 1950 on to the narrow belts. In general, the latter year flatheads were commonly referred to as the "8BA" type for Ford and "8CM" for Mercury. The truck version was identified as an "8RT". Later 1952 and '53 Fords and Mercurys were known as "EAB" and "EAC" respectively. These markings are generally cast into the cylinder heads. The truck versions often had different oil pans to accommodate the different suspensions, and some truck V8's were factory "relieved". The EAB's and EAC's did not have the hardened valve seat inserts like the earlier engines.
Year Displacement
(Cubic Inches)
Bore & Stroke
(Inches)
Torque in Ft Lbs
@ RPM
Maximum
Brake HP
Compression Ratio Head Bolts Notes
1949 Ford 239 3.1875 x 3.750   100 6.80:1 24 2
1949 Mercury 255 3.1875 x 4.000   110 6.80:1 24 3,1
1950 Ford 239 3.1875 x 3.750   100 6.80:1 24 2
1950 Mercury 255 3.1875 x 4.000   110 6.80:1 24 1,3
1951 Ford 239 3.1875 x 3.750   100 6.80:1 24 2
1951 Mercury 255 3.1875 x 4.000   112 6.80:1 24 1,3
1952 Ford 239 3.1875 x 3.750 194 @ 19-2100 110/106 7.2/6.8:1 24 2,5
1952 Mercury 255 3.1875 x 4.000   125 7.20:1 24 1,4
1953 Ford 239 3.1875 x 3.750 194 @ 19-2100 110/106 7.2/6.8:1 24 2,5
1953 Mercury 255 3.1875 x 4.000   125 7.20:1 24 1,4

Notes:
1) Mercury engines of these years had the 4" stroke crankshaft.
2) Used the Ford-Holley two barrel carburetor.
3) Used the Ford-Holley split float, dual downdraft carburetor.
4) Used the Holley Centri-Flo concentric dual carburetor.
5) Lower number is for the Ford truck engine version.

Engine Colors: 
Ford engines were generally dark blue in 1949 and changed to bronze in late '49 production through 1951. For 1952 and 1953 the Ford engine was either tangerine red or green. The Ford truck engines were red from 1948 through 1951, and then changed to green for 1952-53. 

Mercury engines were green in color from 1949 through 1951. From 1952 to 1953 they were either green or tangerine.

For complete crankshaft bearing specs CLICK HERE.

Keep in mind that there were exceptions to these guidelines. Also, remanufactured engines and rebuilt engines of another color could have
been installed in your vehicle during its history. Do not depend on the engine color to verify or identify your engine.

Flathead_BlockID-1949-53.jpg (176867 bytes)

The 1949 to 53 engine blocks were all essentially the same. The primary difference being that Ford installed replaceable hardened valve seat inserts (exhaust side only) on the 1949 to 51 engines. The 1952-53 models did not come from the factory with any hardened valve seat inserts, although they are often found with them now, having had them installed by an engine rebuilder at some time later on. Click on the picture above for an enlarged view of the tops of the cylinders.

Tune-up Specs For These Engines

Go Directly to Engine Parts Drawings

Return to Specifications Homepage

Return to Ford Flathead V8 Homepage

Copyright 2010 - VANPELT PARTS & SERVICE - All rights reserved