Sweet Pea Bunk Bed
Free plans to build a cottage bunk bed! You can build this dream bunk bed with step by step plans from Ana-White.com. Designed and built by Jenny at Birds and Soap.
Again, a huge huge thank you to Jenny from Birds and Soap for sharing her design and photos with you! We'd love to see your bed photos when you build it, so please share!
We'll be adding plans for the roof, pergola, window boxes, shutters and those stairs later this week so stay tuned!
(16) 2x4x8’s
(20) 1x6x8’s
(20) 1x4x8’s
(12) 1x2x8’s
(6) 2x2x8’s
(10) Extra 1x4x8 or 1x6x8 boards for slats (I used half and half)
(3) boxes 1 1/4” pocket hole screws
(2) boxes 2 1/2” pocket hole screws
(1) box 2 ¼” wood screws
Wood glue
Sandpaper
Paint
Primer
Paintbrushes or rollers
Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!
The Bed is divided into four panels. Front, Rear, Left, and Right. The cut list is grouped into boards needed for each completed panel. Roof, Shutters, Window Boxes, and Pergola (all the bells and whistles) will follow. Cut lists for Stairs and Storage Boxes will be listed separately as well.
Front Panel
Front Panel Frame
(2) 2x4’s @ 78” vertical bed posts
(3) 2x4’s @ 77” horizontal braces
(2) 2x4’s @ 30 ½” vertical braces for lower opening
(2) 2x2’s @ 77” bed rails
Front Panel Trim
(4)1x2’s @ 30 ½” lower front panel trim
(2) 1x2’s @ 25 ½” upper front panel trim
Lower Front Panel Pieces
(6) 1x4’s @ 22 ½” lower front panel
(2) 1x6’s @ 22 ½” lower front (these will have arched cuts for window frames)
(8) 1x6’s @ 6 ¼” front lower window panels
(4) 1x4’s @ 6 ¼” front lower window panels
Upper Front Panel Pieces
(2) 1x6’s @ 77” upper front panel pieces (one will have arched cuts for upper window frames)
(1) 1x4 @ 77” upper front panel piece
(4) 1x6’s @15” window edge panel piece
(2) 1x6’s @ 17” center upper panel pieces between windows
Lower Window Sill and Trim
(2) 2x4’s @ 15” with 2 ½” x ¾” notches cut on ends, centered. Lower window sills
(8) 1x2’s @ 13” lower window side trim pieces.
(2) 1x4’s @ 11 ½” lower window top trim, arched.
Upper Window Sill and Trim
(2) 2x4’s @ 20” with 2 ½” x ¾” notches cut on ends, centered. Upper window sills
(8) 1x2’s @ 9 ½” upper window side trim pieces.
(2) 1x4’s @ 16 ½” upper window top trim, arched.
Rear Panel
Rear Panel Frame Pieces
(2) 2x4’s @ 78” vertical bed posts
(3) 2x4’s @ 77” horizontal braces
(2) 2x2’s @ 77” bed rails
Rear Panel Trim
(2)1x2’s @ 30 ½” lower rear panel trim
(2) 1x2’s @ 25 ½” upper rear panel trim
Rear Paneling
(I used leftover scraps from the other panel pieces to create a colorblock effect on the boards resting above the shelves. Instead of one long, solid board, I joined random painted lengths of scraps with pockethole screws to create one long board. This saved me the cost of four boards plus I used my scraps and it looks cool!)
(5) 1x4’s @ 77” rear panel pieces
(7) 1x6’s @ 77” rear panel pieces
Rear Panel Shelving
(2) 1x4’s @ 77” rear panel shelves
(8) 1x4’s @ 45 degrees on one end, 3 ½” on the longest side, trimmed back ½ on the short side to create a shelf bracket.
Side Panels
Side Panel Frame Pieces
(3) 2x4’s @ 38” left and right panel frame
(1) 2x4 @ 21” upper bunk opening vertical frame piece
(1) 2x4 @ 18” upper bunk opening horizontal frame piece
Side Panel Trim
(4) 1x2’s @ 22” upper bunk side panel trim pieces
(4) 1x2’s @ 49” lower bunk side panel trim pieces
Side paneling, Left and Right
(12) 1x4’s @ 38” side panel pieces
(14) 1x6’s @ 38” side panel pieces
(4) 1x6’s @ 18” upper side panel pieces near opening
Front Frame
Starting with the front frame, attach the 78” vertical bed posts together with the top horizontal support. The posts will be turned in so that the 1 ½” edge is on face with the front panel. The 77” top piece is attached using 2 ½” pockethole screws drilled from the underside and wood glue on the insides of the bed posts and is also turned so that the 1 ½” edge is on face.
Next, the other two 77” horizontal frame pieces will be attached on the inside of the posts. These will be turned on their sides, with the widest face of the board facing out (on my first go round, I had them turned the other way, which gave no structural integrity to the bed rails. Don’t do that.). The middle board is screwed in and glued at 25 ½” down from the bottom of the first board, and the bottom board gets screwed in and glued at 30 ½” from the bottom of the middle board. These pocketholes should be screwed in from the back of the frame and the 2x4’s should sit flush with the front edge of the bed posts.
Last for the frame, the two vertical 2x4 pieces that will frame out the bottom opening are screwed in with pocketholes as well, each at 26” from the inside edge of the bed posts (this should leave a center opening of 25”). h
Check for level on all boards.
Mattress Cleats
Attach the 2x2 rails that will be used to support the mattress slats to the bottom and middle 2x4 horizontal boards on the inside of the frame. Using 2 ¼” screws pre-drilled and countersunk every 15”, and wood glue the entire length, attach the bottom rail flush with the bottom edge of the lower board, and for the middle section, attach the 2x2 rail so that it is flush with the top of the middle board. This will give a little more head room in the lower bunk area.
Front Inside Trim
Attach trim pieces to vertical posts. Using 2 ¼” screws, again, pre-drill and countersink the edge trim into the bed posts. For the Front Panel, They are attached with the wide edge facing out and these edge pieces will be flush with the front face of the bed frame.
Front Upper Paneling Window Cutouts
Panel construction: Beginning with the upper portion, if you would like arched windows, you will need to measure and cut arches into this board. If you are okay with square windows you can skip this step. To figure out height and width of the arches, I used a very complicated method:
First you measure 15 3/4 inches in from the edge of your board and mark it. Then, you measure another 13 ½ inches from that mark and make a line. You now have the width of your arch measured. Do this exact same thing starting from the opposite end of the board measuring inward. The window openings will be even from the edges, and you should have an 18 ½ inch space in the center between the two marks.
Now find something big and round. I found a flower pot from something I let die hanging out in my driveway. You want a large enough circle so that you will get a slight arch and won’t be cutting too high into your board. Line your object up so that it is within your two marks and trace around it. Voila! A perfect arch!
My advice here is to cut out one side with a jigsaw, then take that scrap and use it to trace your next arch for the other window. I did not do this and my window arches ended up being slightly off, which made for trouble when I tried to make identical shutters. Bottom line: however you get your arch, whether you trace around a garbage can, pizza pan, or dreamcatcher- make sure it matches the second one. You can’t really tell from looking at my finished bed that they are uneven, but trimming it out was a real pain.
NOTE: Short panel pieces on outsides of top windows are 15" long. 15 3/4" long marks the start of the optional arch cutouts.
Front Paneling
Now that your window arches are cut in, you can move on to the next panel pieces. I advise you wait and dry fit all of the pieces before you start nailing and gluing them in. Not all boards are perfectly straight and make for some wonky lines. I happened to purchase culled lumber for my panels at a discount, and some of my boards were warped so bad that I had to sand and trim to make a nice fit. It’s probably worth the extra $5 to just buy good boards in the first place. I just tell myself that the crooked boards add to the charm, lol.
Back to the bed.
Lay your bed frame face down on a flat level surface and place the boards so they are resting on top of your trim pieces. I used a scrap of wood under the center of the long boards so they rest even the entire width of the bed. Align the top arched board in place, and the remaining two 77” 1x4 and 1x6 boards at the bottom portion of the upper bunk panel. Before fitting the smaller pieces that will separate the window spaces, I glued the edges together and used my nailer at 45 degrees, this made these smaller pieces even and easier to deal with when it came time to attach them to the panel. I recommend clamping these pieces together and allowing them to dry.
Cover the back side of the trim pieces with glue and lay your first board into place. Run a bead of wood glue on the top and bottom edge of the board as well. Using your nailgun, nail the top board to the trim pieces on each end. You can also toenail a few shots into the top frame piece to make sure your board is secure. Take time to make sure that your board is nailed level and even.
Next, with the smaller 15 inch sections, run a bead of glue on the edges and nail into place. This will be easy on the edge pieces, but for the center section that is between the windows, you will have to put a block underneath to keep it level with the rest of the panel. Also, make sure to align the center section with the marks between your arches. The center section will be ¾ of an inch in from the edge of the top window arch. This allows for trim to line up flush inside the window opening.
Continue fitting your boards into place, checking for level, nailing and gluing down the entire width. When you are finished, stand up your panel and wipe clean any glue that has dripped to the other side (there will be glue). I used a large 4’ pipe clamp to hold everything in place while it dried. Note: It may be necessary to throw in a few 1 ½”pockethole screws to secure the wider panel pieces into place. I did not do this, but it sounds like a good idea; especially in the center section between the windows.
So, how’s it going? Are you still with me? If so, get ready for the bottom portion, By now, the top section should look like it’s getting there, you might be a little concerned with the edges around the window openings, but they will be secured when it is time for the trim.
Lay your panel down again, and dry fit the lower sections. Again, if you would like your lower windows arched, take your 22 ½” long 1x6, measure in 7 inches from each end, and make your arch between these two points; this time using a smaller round object ( like a cake pan or a floor lamp). I’m sure there are simple instructions somewhere on how to make a perfect arch without tracing random objects, but I haven’t googled them yet. The pieces beside the window opening are only 6 ¼” long, making them almost seem pointless, but trust me, they are necessary for the cute factor on this bed.
Starting with the top 1x4 that is 22 ½ ” wide, glue and nail it into place, checking for level. Then, attach the window arch board to the edge trim followed by the smaller boards on each end (gluing and nailing as you go) and the final two boards that sit below the window. If you notice that your shorter boards do not align perfectly on edge around the window opening, it will be okay. The front side of the panel will be covered with trim, just make an attempt to keep them level. Unless you are going with a “crooked house” theme, do your best to keep things even.
Do this to both sides of the center opening and you will see your bed taking shape. This was the part of the process that got me really excited, because my vision was becoming reality! Remember to wipe off any excess glue, because you will be crying real tears if you have to scrape it off when it has dried. So I have heard.
NOTE: Short panel pieces on outsides of top windows are 15" long. 15 3/4" long marks the start of the optional arch cutouts.
NOTE: On the lower front panel measurement, the small boards along the sides of the windows are mislabeled. 1x6's are 1x4's - you'll see that these boards are wider in width (Ana mistake here!)
Upper Window Sills
Next you will be creating a window sill. Stand up your panel and lean it against something sturdy to work. Starting with the upper section, measure the width of you windows. If your cutting is correct, they should be 15 inches wide. Using the 20 inch 2x4 for the sill piece, you are going to create a notch on each end that is roughly 2 ½ “ long and ¾” wide. Mark your board lengthwise on center and also mark two lines at 2 ½” in from each edge. Carefully measure 3/8” out from the center line on each side and mark lengthwise.
Cut out this rectangular shaped notch with a jigsaw and dry fit into your window opening. It should lie flat resting on the board below the window space and each notch should secure it to the adjacent panel pieces. It took me a little effort to get a nice fit; a little tweaking might be required.
When you are finished, glue the sill into place on all edges and use your nailgun to secure it into position. Do this for each upper window.
Lower Window Sills
Now for the lower windows, this is more of the same. The lower window opening should measure ten inches wide, therefore the sill piece will be 2x4x15 inches wide. Again, a 2 ½” x ¾” notch on center will complete the lower sills. Glue and nail into place.
Window Side Trim
Trimming out the windows: The upper and lower windows are trimmed out with 1x2 material. When it came time to trim out my windows, instead of painting and precutting each piece, I chose to paint a 1x2x8 at length, cut as I needed, and touched up as I went. Due to the nature of trim work, things never seem to go perfect, and trim pieces end up a hair to long or too short so I opted to measure and cut as I went versus having too short of boards that end up in the scrap bin.
Starting with the interior edge of the window, measure the length from the top of the window sill to the top of the window opening. If you made arches, your trim will fit in that nice little ¾” space. The top windows should measure roughly 9 ½” tall and the lower window interior trim should measure roughly 13” tall. Glue the trim on either side of the window opening, keeping the outside facing edges flush and nailing into place.
Using more 1x2 material, the face trim will be added on each side of the windows. The measurements for length will be the same as the interior trim, also nailed and glued and kept flush the edge of the interior trim edge. When you are finished nailing and gluing, the sides of the windows will be secure and smooth.
Arch Trim
To trim out the top of the windows I used a 1x4 board cut to the width of the outside trim. Again, for the upper windows, this board should be roughly 16 ½” wide and for the lower windows, it should measure 11 ½” wide. Fit it into place so it rests on top of the trim, and with a pencil, trace the arch pattern from the window opening onto the back of your board.
To get the outside arch, I measured ½” up from the bottom edge of the board and drew another arch freehanded. I tried to keep an even 1 ½” width all the way around. It is not that hard, but if you are intimidated, there is always finding another circular object to trace. Cut out both of these lines with your jigsaw and sand the edges smooth. I swear my lines were *perfect* because I’m crazy like that. But after I got went to town with my jigsaw it didn’t seem to matter much anyway; even at my best, I was all over the place ( I blame it on my blade). Needless to say, it took some serious sanding to get things nice and even.
Now if you made your windows square, things just got a whole lot easier because all you need is a piece of 1x2 cut to length.
Use glue and a nailgun secure the top trim into place on all four windows.
Boom! That’s it. Your front panel is finished! If you want to add shutters and window boxes you can add them next. I advise holding off on the roof and pergola till the end- those extras will follow later in the plan. There’s no getting through a doorway with the roof installed and a pergola hanging off the front! Take some time to look over your finished panel to make sure there are no nailheads sticking out. Use a nail set to put them below grade. Fill nail holes, sand any rough edges, touch up paint, and so on.
Rear Panel Framing
The rear panel frame is assembled identically to the front panel. The 78” vertical posts will be attached with the horizontal top piece using 2 ½” pockethole screws and glue.
The middle horizontal frame piece is screwed in at 25 ½” below the top piece using pockethole screws drilled from the backside of the frame and also lying flush with the outside post edges. The bottom frame will be attached at 30 ½” from below the middle piece in the same manner.
Rear Panel Trim
Attach the four trim pieces. 25 ½” 1x2’s in the upper section and 30 ½” 1x2’s in the lower section. They should be pre drilled, countersunk, glued, and screwed with 2 ¼” wood screws so that they sit flush with the rear of the panel frame.
Attaching the rails
Again, these rails are attached in the same manner as you did with the front panel. Glue, pre-drill and countersink 2 ¼” wood screws every 15 inches across the rails to secure them. The bottom rail sits flush with the bottom edge of the 2x4 frame and the top rail sits flush with the top edge of the 2x4 frame.
Assembling the rear panel sections:
Now this should be really easy, after all it’s just horizontally stacked boards nailed into place. However, unlike the front panel, these boards are not broken up by center sections and extra trim. Because these panels are so long, the boards tend to be a little flimsy and want to sag in the middle. I solved this problem by using pockethole screws to join the boards on the back side.
This time, when you lay the panel down, the “pretty side” will be facing you. With your trim already in place, you can dry fit the boards to see how they will fit within the space. For the upper section, I used three, solid 1x6’s at 77” long to fill the bottom portion below the shelf. For the space above the shelf, instead of solid boards, I used scraps left over from my other cuts. I primed and painted scrap boards in four different colors, distressed the edges, then joined them together at random with 1 ½” pockethole screws on the back, giving the panel a color-block effect. This saved some money and used up a large amount of scrap that would otherwise still have been sitting on my patio. If you choose to do this, keep in mind that you want to be consistent with board size; I used 1x4 material all the way across for one row, and 1x6 material for the second.
With your boards fitted into place, remove them from the section and turn them over. Using your Kreg Jig, drill pocketholes along the top and bottom edge of your boards roughly every 15”. Alternate the pockethole placement on each row to get a solid panel. Glue and screw your panel pieces together. Wipe the excess glue before it dries.
Also, I drilled pocketholes on the ends of the boards. This rear panel is heavy!! Because of the weight of the boards, the panel almost wants to sag in the middle, so I made sure to place pocketholes along the outer edges for a solid frame attachment.
This was time consuming and I burned through 1 ½” pocket screws rather quick, but the panel ended up strong and sturdy. To attach your boards to your panel, you will need to stand it up while you secure the section with pockethole screws. Use a scrap block to make sure your boards are flush with the interior edge while you glue and screw.
For the lower section, you want to create your panel in the same manner. Dry fit your boards, drill pocketholes around the edges, and glue and screw until you have one large plank. Notice the board size on the bottom section; it is made up of (4) 1x4’s and (3) 1x6’s all at 77” long. For the color-blocking on the bottom section, I used (2) 1x6 boards, making my shelf just a few inches lower than the upstairs bunk. I did that because there is limited headroom in the lower section and figured a lower sitting shelf would be better. Totally up to you.
Attaching the Shelf
The shelf is so simple, yet adds so much to the inside of the bed. In order to attach the shelf across the bed, I made simple brackets by cutting down piece of 1x4 and making 45 degree cuts.
Start with a board and measure 3 ½”. This measurement will be the long side of he angled piece. Adjust your miter saw to cut a 45 degree angle. You will get a perfect right triangle. Then, trim off ½” in from the point on one side, with a 90 degree straight cut. This createos a little bracket that lets a 1x4 board rest nicely on top with a ½” overhang.
Once you have made the eight brackets, find the third board down from the top of your panel. Measure 15” in from each end and mark. Attach the bracket with a nailer and glue, keeping it flush with the top edge of the third board. Measure another 15” in from the two brackets you just nailed, mark and attach the remaining two brackets for your first shelf, checking for level.
Attach the 1x4x77” shelf by gluing it to the rear panel and brackets. Use your nailer to hold it in place. Wipe any excess glue and allow it to dry.
Done! This sucker is heavy. You need a helper to move this unless you want a hernia. Keep it secure so it won’t fall over while you are working on other aspects of the plan.
Side Panels
The side panels will go up rather fast. Instead of gluing the frame pieces together, you will just be screwing them in with pockethole screws. This way, the bed can be disassembled, allowing it to be moved inside; or if you should happen to join Witness Protection and need to flee the state, you can take it down in ten minutes flat.
Measure 25 ½” down from the top of the vertical frame pieces on each panel and mark. Do this on all four vertical posts.
Find your (3) 2x4 frame pieces measuring 38” in length and pre-drill the board ends with pocketholes so they are ready to screw on the fly (I even placed the 2 ½” screws in the holes ahead of time for lightning fast drilling action).
To put the bed together, you can either lean the panel against a wall or have someone help you hold it up while you attach the frame pieces to the first panel. The panels are heavy and can be a little bit of a balancing act before you get the first side secured; that’s why I recommend having the screws in place and ready to go.
Starting with the rear panel, attach the side frame pieces on each end of your panel so that the top of the board sits flush with your marks, drilling the screws from the inside of the bed. After these two boards are in place, attach the last 38” piece to the very top of the panel’s left post. It should mount flush with the post.
Attaching Front Panel
Next, you will need to maneuver the front panel into position and screw opposite ends of the side frame pieces into place. When all three pieces are secured, you can let go!
Stair Side Framing
To attach the frame for the upper wall near the top bunk opening, find your 22” vertical piece and drill pocketholes into each end. Next, drill pocketholes into only one end of the last 18” frame piece. Join the boards together at a right angle, the 22” board should be aligned vertically, wit h the 18” piece lying horizontally across the top. Take this “L” shaped piece and screw it into the upper right side panel.
Attaching the Trim
All trim will rest flush against the outside edges of the side panels. Below the center frame support on each side panel of the bed, you will need to attach your trim pieces. Using (4) 1x2 strips cut at 49” long; pre-drill, countersink, and drill into the vertical posts with 2 ¼” screws. Remember the side panels are not glued in for this step.
Next is the trim for the upper portion of the side panels. Attach (4) 22” strips in the upper section with the same method.
Side Panels
If your boards are pre-cut and painted, this will go very fast. Using wood glue and a nail gun, from the inside of the bed, start at the top and work your way down each side. The upper sections will use (4) 1x6 boards on each side. The left panel will be 38” long and the right will only be 14 ½” long to fit that tiny half wall. Apply glue to the back side of the trim pieces and glue between the board edges while you nail the boards into place along the trim.
On the lower sections, I alternated between (6) 1x4’s and (5) 1x6’s to fill in each side until you reach the bottom of the bed. There will be a small ½” gap along the bottom of the side panels (it serves no purpose, just too small to do anything with). Wipe excess glue and allow the panels to dry.
Note: When it is time to move the bed, you can remove each panel by unscrewing the trim pieces along each post. The panel sections will come out whole and then all you have to do is disassemble the side frame. Easy Peasy!
Mattress Slats
I made the slats for the upper and lower bunks out of 1x4 and 1x6 boards cut at 41” long. I placed them close together (8-10” apart) and lined each bunk along the rails. Because this bed is slightly larger than a standard twin mattress (For good reason! Nobody wants to get bloody knuckles trying to change the sheets), the top bunk end slats need to be touching the side panels. When you enter the upstairs bunk, there will be a gap at the end of the bed. Make sure a board is in place to fill the space and create a little platform. For extra cool points: Paint the underside of the boards that line the upper bunk. The lucky child who sleeps below will be staring at those boards every night of his/her life before they drift into sleep. I painted the slats different colors from my leftover paint jars (and even cooler: cover the underside of the upper mattress with an extra fitted sheet- fun characters or something or other that kids like).
- Log in or register to post comments
- Printer-friendly version
- Send by email
- PDF version
Comments
birdsandsoap replied on Permalink
Thank You, Ana!
Thanks for all your help, I'm so excited to share this plan!
mach170 replied on Permalink
It looks like the model in
It looks like the model in the pictures was done in SketchUp. If so would it be possible to get the SketchUp file?
Maria in Maui replied on Permalink
Amazing!!!
This is absolutely amazing! I just adore it. Great job, seriously, this is the cutest, most detailed bed I've ever seen! I am completely inspired, I gotta come up with a boys themed one!
Thank you both for sharing!
dmcarwin replied on Permalink
Awesome!
So very Beautiful! Thanks so much for sharing!
abbpim replied on Permalink
This is awesome!
About a month ago, I made the farmhousre storage bed that Jenny posted. Directly after that project, I began revamping my kids' ikea bunk bed from something very boring to something imaginative. I decided to make it into an L shaped loft/playhouse bed, but I've put the project on hold in order to gather inspiration while completing some toys for inside the playhouse. (Yeah I was really just about to put the walls up when my husband reminded me that I won't be able to get anything big inside the playhouse if I put the walls up first... DUH!). So I've been trying to design in my head the perfect loft/playhouse bed for my girls when suddenly these plans popped up today! The strange thing is that I was truly messing up my brain trying to figure out the best solution for storage stairs. It's like a telepathic message was sent from my brain to the ana white site! This bed is the perfect style for my kids, and now hours of my time had been saved! Thanks Jenny and Ana! I'm starting this project ASAP! You are both creative geniuses!
birdsandsoap replied on Permalink
That is awesome!
I can't wait to see your brag post, I love it when things fall into place like that. Thanks for your kind words.
hoffer5353 replied on Permalink
Fab!
This is absolutely fab, when I saw it I felt like I would love to crawl in and go to bed. You have some very lucky kids! Thanks for sharing your creation!
redhead_61 replied on Permalink
Completely PERFECT
This is maybe the most amazing thing I have seen on this sight besides Ana building ya know a house! I have been wanting to ask her to design a tree house inspired bunk bed for my kids. The over all design is VERY similar to what you have here. I need it for a queen and full bed, I will have to see if I can modify to come up with that! Maybe next year you will be seeing my brag post! Amazing job it is so darling.
I am pinning you because you deserve the recognition.
birdsandsoap replied on Permalink
Thanks!
This bed is like having the Ultimate fort in your room that you never have to take down. If you made it a queen/full size, your kids would feel like they get to sleep in a mansion! Get to work, because I would love to see what you come up with!
jesikuh123 replied on Permalink
Missing Plan Link
Hi there!
I am trying to download the PDF file for this bed but the link seems to be broken. Can you relink it or email it to me please- this is a perfect spring-time -lay-off job for my husband!
my email is j.mccloskeywarner@gmail.com
Tank You!
Pages