Brewing
Instructions
In a very
clean Stock Pot combine 1 gallon of Bottled Spring Water with the Honey
and Irish Moss. Rinse honey jar with water from the pot. Heat to 180 degrees
F. Reduce the heat and hold the temperature between 175 and 180 degrees
F. for 20 minutes. Stir occasionally and skim any white film off of the
surface. Do not allow to boil.
Remove
pot from the heat and place it in a sink of cold water to reduce its temperature.
Stir every 10 minutes and then change the sink water. Do this 3 times.
Add 1
gallon of bottled spring water and acid blend, yeast hulls, yeast extract,
pectic enzyme, and grape tannin per recipe chart above. Stir well.
|
Preparing
the Must (Traditional Mead Makers skip to Starting Fermentation)
Remove
can labels and open fruit puree or grape concentrate.
Pour contents
into the brew pot and stir well. Use mixture from pot to rinse out the
can.
|
Starting
Fermentation
Clean
and sanitize a 3 gallon carboy, rubber stopper, air lock and funnel.
Open the
packet of wine yeast and pour it into the carboy.
Use the
funnel to pour the Must onto the carboy.
Place
the stopper and air lock into the carboy and fill the air lock half way
with water.
Store
at room temperature. Ferment for 3 weeks.
|
1st
Racking
Racking
mead should be done by gently siphoning. We do not recommend using wine
pumps or filters. Mead is very susceptible to oxidation.
Move the
primary fermenter into racking position at least 2 days before actually
transferring the mead. This will allow time for the sediment to settle
back down.
Clean
and sanitize a 3 gallon glass carboy, stopper, air lock and siphon set
up.
Crush
3 Campden Tablets and place them into the carboy. Gently siphon the mead
from the primary fermenter into the bottom of the carboy. Be careful not
to disturb the sediment.
Add distilled
water to bring the level of the mead up to the bottom of the carboy neck.
Close
the carboy with an air lock and allow to ferment in a dark place for at
least 30 days but not more than 45 days.
|
2nd
Racking
Repeat
the 1st Racking Step but this time use only 2 crushed Campden Tablets and
Citric Acid..
Allow
the mead to rest in a dark place at least 30 to 45 days or until it clears.
To check clarity, hold a flash light on one side of the carboy and look
at the light from the other. When you can clearly see the bulb of the light
the mead is clear.
Sweet
mead makers must add 1-1/2 teaspoons of potassium sorbate at this time.
|
3rd
Racking
There
is no substitute for time when making mead. The more mature the mead is
prior to bottling the better it will be. A third racking will allow the
mead to brighten and age. All recipes except Sweet Mead do not use any
additives on this racking.
Sweet
mead makers must add wine conditioner at this time.
|
Bottling
Mead can
be bottled as you would wine or beer. I prefer to bottle in 375ml wine
bottles or 7oz clear beer bottles. These smaller sizes reduce waste caused
by leftovers. If the beer bottle method is used the caps must be the oxygen
barrier type. Wine bottles should be closed with a 1-3/4 inch cork.
You can
make your mead still, sparkling or both. Sparkling mead can only be sweetened
with a sugar substitute and must be bottled in beer bottles or champagne
bottles with special corks and wires.
Clean
and sanitize your bottles, caps, siphon and bottle filling equipment. Gently
fill each bottle but do not cap until all are filled.
When filling
is complete you have the option of making some of the mead sparkling. To
do this, add 1/2 teaspoon of corn sugar to each sparkling bottle.
Cap or
cork the bottles. Store them upright in a dark cool place. Mead will take
time to age and in my experience it will under go many changes. A batch
which tastes great a bottling time may taste bad after 3 months in the
bottle and then fabulous at 6 months.
|