Interested in Buliding a custom fishing rod? This article is part 1 of custom rod building titled: Selecting Components
Captain Stephen Altenbach
When I told Mike I was going to be building some sword rods, he asked me to write an article for the website, which I was more than happy to do. I hope ya’ll enjoy, and learn something! I would really appreciate any and all feedback. I recently started a little company called BlueWater Custom Rods LLC (mainly to get stuff cheaper with wholesale pricing) so I’m looking for business!
I really needed some good #50 rods to replace the ones I was previously fishing with. My old ones had small roller guides which would not accommodate large bimini knots or wind-on leaders. Also, they were too long for my taste and the components were bottom of the line. I started looking at big game rods, comparing components and types. I learned a great deal on this project, and gained a lot of great advice from other rod builders and experts from Biscayne Rods, Chaos Rods, J&M Rods, Scott with American Rod Co, Tek with Reel Pro Shop, Justin on the forum and others. Stand up fishing is a relatively new style, and the equipment which is helping anglers tackle giants without a chair is constantly evolving. This article will be one of a few that will take ya’ll through my entire rod building process.
The first step in choosing components came from deciding what species I was targeting. Obviously swordfish were top of the list, but I also wanted these rods to handle anything my Tiagra T-50WLRSA’s will (thanks Tek!), including fairly large Marlin. There are 4 main parts of a rod; the blank, the butt, the grip and the guides. The blank is by far the most user specific, and must be tailored to your needs.
After comparing many types, I decided on a Seeker TS55XHB 50-80 Extra Fast taper blank. The Blank has a softer tip which will help prevent pulled hooks while swording, and will also give the rod some bend with smaller fish. I did not want a broomstick which would only bend under the pressure of a #300 tuna. Also, I decided that the length of the rod should be 5’6”. I am a pretty short guy, and my old 6’ rods seemed a little hard to control at times. Some stand up rods are now being built under 5’. This is a little too extreme for my taste, and also is not practical because our boat has a large swim platform to maneuver around. The boat design, your height, arm length, harness style and more should all be considered when determining the length of the rod.
Now that I had decided on a blank, the guides were the next on my list. I knew I was going to be using Wind-On leaders so my choices were limited to the following:
- Aftco Wind-On Guides
- Stuart Large Roller Guides
- Winthrop Tool 50-130 Ball Bearing Guides
Aftco Wind-On guides are of course the standard, and they are certainly an excellent, lifetime guide. However, once I took a good look at the new Winthrop Tool guides, I was hooked. Each guide has two sealed ball bearings, a titanium roller, and has a great looking solid aluminum frame. Each guide has a 5/16 of an inch gap (enough to fit a #2 pencil) between the roller and frame, allowing adequate room for wind-ons over 700lbs. They are more costly, but I think it will be a good investment in the long run. You can check out these guides at www.winthroptool.com. Once I chose the style of guides, I had to decide on how many guides, and what size. After subtracting the length of the butt, grip and the tip top guide, I was left with about 33’’ of blank on which to place guides. For these rods I am using the following guides:
- #50-130 Stripper #SR2
- #50-130 Guide #R3-6
- #50-130 Aluminum Tip Top - Size 12
This hand picked set was perfect for my rods. Also, for those who prefer the Aftco style guides, Winthrop has just released a new set of guides called the Excel series. They offer Winthrop performance in a more standard Aftco design, but on steroids, and much more sleek. All Winthrop guides are available in Titanium, Gold, Platinum and Black. Also, for those who demand the very best, Winthrop offers guides with solid Titanium guide frames.
The next decision was what style butt to use. Of course, Aftco is standard. I had a hard time trying to decide between a straight butt and the newly popular short bent butts. Both have their pluses. Short bent butts are better for swords and tuna, but since marlin fight more on the surface, a bent butt puts the rod at a bad angle for stand up fishing. Finally I decided to go the extra step and use Aftco Storabutts with an extra straight butt. The Storabutt is a great product, and allows you to disconnect the butt from the reel seat, the same as you would detach your normal unibutt from the rod. This allows you to change from one butt to the other without taking your reel off. You can even change mid fight! (This is IGFA legal, so long as the angler makes the switch.) I went with an all black finish because Aftco’s gold is kind of orangey and clashes with the Tiagras.
Last but not least, the grip. In this area, you are really left with three choices, EVA, Hypalon and Leather. Since I take extra good care of my equipment, and these rods are going to be eye candy, I am using leather grips from Biscayne Rods. I discovered the huge debate between rod builders about grip lengths for stand up rods. Some say that grips don’t matter, since both hands should be on the reel in true stand up scenario. Others argue that grips should be up to 15” long. I split the difference. Eddie Carman of Biscayne Rod custom made me four of their famous leather grips in a 12” length in the appropriate diameter for my blank.
Now that I had all my components selected and ordered, the next step was to design the rod from butt to tip. This includes deciding on wrap patterns, spining the rod, sighting the guides, creating a weave pattern and much more.
Heres all the components, except for the guides, they have not yet arrived.
This shows the Storabutt reel seat without the butt attached. You can even flip the seat around and the reel will sit 2 inches closer to the grip.
This shows the Storabutt reel seat without the butt attached. You can even flip the seat around and the reel will sit 2 inches closer to the grip.
Here is one grip that is near completion. It has already been attached, sanded, sealed, sanded again, wrapped, finished and wrapped again. Design threads will be added and then a final coat of finish will be applied.
Comment on this article in the fishing forums
