Welcome to The home of the "Backyard Renegade" |
Kits for Calico
Hunter, and Little Joe!
Designed for the "First time
builder"!
"I just want to build boats!" As you will see, this has
not changed. It was not easy going from being a carpenter to being a boat
builder a few years back, everyone was still trying to keep this little hobby a
secret only enjoyed by an elite few. I built my first boat thanks to Dynamite
Payson ( the king of the backyard renegades ) and I still feel that his books
are the ultimate authority on good cheap backyard boat building. However, being
more interested in fishing than sailing, I have come up with some more modern
variations which I feel are more geared toward small engines as opposed to
engine power being an afterthought, as with many of the classic hulls of the
first half of the last century. Hulls from Bolger and Gardner and Monk which
many of the "major" designers are still drawing and hawking as their
own..(Right Anne?)
So Ladies and Gentlemen
and SmallBoat enthusiasts of all ages! I proudly present two of my best selling
boats!
"Little Joe" and "Calico Hunter"
My "Little Joe" Pram Kit
As you can see, Little Joe stays very dry. With one small passenger or being towed with minimal equipment, the sides and transoms don't even get wet! I have been told that this boat should sail pretty well, I have a 40 sq foot sail I am going to try as soon as it gets a little warmer up here. |
Complete Kit of Marine Occume Plywood includes everything you need to build "Little Joe" $795 + Shipping Plans for Little Joe are available for a limited time on four, 17" x 22" fully detailed blueprints. These sell for $30.00* |
The kit for "Little Joe" comes with:
Bow Transom shaped and beveled...ready to
go. Quarter Knees pre beveled and marked. Full size bottom and side panels of Marine Occume. Bulkheads and seat tops, pre beveled and marked for installation. Transom with motor board, cut to size and pre beveled. Seat risers and supports all cut to size and pre beveled. Skegs, Gunnels and Oarlock blocks. |
Enough Stainless Steel Screws and Bronze
Silicone nails to build the boat. Two part Epoxy, Thickener and 80 feet each or 3" and 2" Fiberglass Tape, enough to put a double layer inside and outside on all stitch and tape seams. I also include many extras that help in the construction such as a roll of 18 guage copper wire, copper wire nails and a roll of masking tape. |
Click here for more information about Little Joe.
"Calico Hunter" Kit
All kits are made with 5 and 9 Ply, Marine Occume Plywood, with a BS1088 rating. If you wish to use your own materials, build from a set of my plans |
Complete Kit of Marine Occume Plywood includes everything you need to build "Calico hunter" $995 + Shipping Plans for Calico Hunter $25.00* |
The kit for "Calico Hunter" comes complete with:
Stem, shaped and beveled...ready to go. Breast hook and Quarter Knees pre beveled and marked. Full size bottom and side panels of Marine Occume. Bulkheads and seat tops, pre beveled and marked for installation. Transom with motorboard, cut to size and pre beveled. Seat risers and supports all cut to size and pre beveled. |
Skegs, Tapered Gunnels and Oarlock
blocks. Enough Stainless Steel Screws and Bronze Silicone nails to build the boat. Two part Epoxy, Thickener and 100 feet of Fiberglass Tape, enough to put a double layer inside and outside on all stitch and tape seams. I also include, many extras that help in the construction such as a roll of 18 guage copper wire, copper wire nails and a roll of masking tape. |
Click here for more information about "Calico Hunter" and all of the "Classic Scrappies"
My kits come complete with
everything you need to build a boat from start to finish all you add
is the time, a few tools and the paint! You get a full set of plans and all of
the top quality materials, adhesives, and fastenings you need. All of the parts
are pre-cut of Marine Occume plywood (BS 1088 marine rating), pre-beveled, and
marked, ready to assemble.
Accessory kits with Hand lashed oars, Bronze
oarlocks and Bow hook can be purchased separately, call for details.
Not familiar with stitch and tape construction? No problem! For a limited time I will include a copy of Dynamite Payson's book "Build the new Instant Boats" with every kit sold, This book not only includes plans for 6 small stitch and tape boats, but it is also a complete start to finish manual on stitch and tape boat building from picking out the nails to the final coat of paint. The first section of the book spells out all of the methods and techniques necessary for the beginning boat builder to be successful. And of course if you get stuck give me a buzz by e-mail, my message board, or by phone I'll be happy to help.
Limited time special!
Plans for "Little Joe" and
"Calico Hunter" are now available
fully detailed on four 17" X 22"
blueprints with complete instructions.
Click here
for the secure order form
[ SMALLBOATS
HOME ] [ SCOTTY'S BOATS ] [ BOAT
KITS ] [ BOAT PLANS ] [CURRENT PROJECTS ]
[
DYNAMITE PAYSON ] [
FREE PLANS BY IRA EINSTEEN ] [ CONTACT
SCOTTY ] [ LINKS ] [
ORDER FORM
]
*For plans shipped outside the US add $3.50 Shipping
This document maintained by The Backyard
Renegade.
Do not copy this stuff for other than personal use. If you would
like to use any of the photos, graphics, or text information for any other
purpose, please contact me first. I can at times be pretty
reasonable...
SmallBoats.com /
IDesigns, LLC
55 Westbrook Road -
P.O. Box 303 -
Centerbrook, CT 06409
860-767-3473