Index Page


	HI-VOLT PCB REPLACES 14 PARTS ON HI VOLT SECTIONS OF EITHER BALLY OR STERNS SOLENOID DRIVER BOARDS. TESTED FOR OVER 7000 HOURS WITH NO BROWNOUTS OR FAILURES. SIMPLY REMOVE ORIGINAL PARTS, SOLDER IN 4 WIRES AND PLUG IN PCB. $34.00 INCLUDES SHIPPING TO USA AND CANADA.	BALLY/STERNS CHIP SET FOR MC6800 MPU AND CLOCK CIRCUIT. $15.00 INCLUDES SHIPPING USA/CANADA
	SINCE 1995- THE THEATER OF MAGIC ANIMATED SAW KIT HAS BEEN A TOP SELLER. AVAILABLE FOR GAME ROMS 1.1 THRU 1.3. $75.00 INCLUDES METAL SAW BLADE AND SHIPPING USA/CANADA		ADD-ON SWITCH WILL POST A CREDIT FOR EACH ONE REMOVED. SIMPLE INSTALLATION, BOLT ADD-ON SWITCH ON TOP OF EXISTING START SWITCH. SOLDER TWO WIRES TO COIN SWITCH (NEXT TO HINGE). $15.00 INCLUDES SHIPPING USA/CANADA
BOARDS ACCEPTED ARE WILLIAMS LEVEL 6/7 CPU & DRIVER BOARD- BALLY SQUAWK & TALK , - 17 AND -35 MPU¡¯S. STERNS 100 AND 200 MPU.	IF MPU HAS ANY PREVIOUS ¡®REPAIRS¡¯ OR IS ACID DAMAGED, JPEGS SHOULD BE SUBMITTED FOR EVALUATION BEFORE SHIPPING . tcallahan@pin-logic.com	NO BOARDS ACCEPTED WITH ¡°REPAIR KITS¡± INSTALLED. STANDARD REPAIR CHARGE IS $75.00 (PARTS/ LABOR/ RETURN POSTAGE).	BALLY/ WILLIAMS BOARD REPAIRS
	INSTALL A MC6802 PROCESSOR IN PLACE OF AN OBSOLETE MC6800 IN BALLY AND STERNS MPU'S.	COMPLETE INSTALLATION KIT INCLUDES ADAPTER MODULE, FRESH MC6802 IC, 14 PIN SOCKET AND FRESH 74LS37 IC. COMPLETE UNIT AS SHOWN IS $42.00 INCLUDING SHIPPING USA/CANADA	TO INSTALL ADAPTER AND NEW IC15, REMOVE THE MC6800 FROM U9 SOCKET. PLUG IN THE ADAPTER WITH MC6802 ON BOARD. IF THE IC 15 IS IN A SOCKET THEN REMOVE THAT IC AND INSTALL THE REWORKED 74LS 37 SUPPLIED. IF FACTORY IC 15 IS STILL IN PLACE THEN REMOVE THAT IC AND INSTALL THE MACHINE PIN SOCKET (SUPPLIED). THE JUMPER FROM THE ADAPTER PLUGS INTO A TERMINAL SOLDERED TO PIN 5 ON IC15 . MPU IS READY TO START. TO RESTORE MPU BACK TO SYSTEM WITH MC6800 SIMPLY REMOVE THE ADAPTER AND MODIFIED IC15 AND INSTALL A MC6800 ALONG WITH A STANDARD IC15.
	XENON CLEAR ACRYLIC TRANSPORT TUBE.1 1/2" OD WITH .120 WALL X 12 1/4" LONG. OFFERED SEPARATELY FOR $14.50. (INCLUDES SHIPPING USA/CANADA).	XENON MOUNTING HARDWARE HARDWARE	XENON BLUE LED LITE STRIP-$36.00 XENON LIGHT STRIP AND TUBE $45.00 XENON LIGHT STRIP, TUBE, AND MOUNTING HARDWARE $49.00 PAYPAL ADDRESS tcallahan@pin-logic.com
	BRAND NEW WILLIAMS 6 VOLT FLIPPER RELAY FOUND ON ALL GAMES FROM WORLD CUP THRU EARLY WPC $15.00 INCLUDES SHIPPING USA/ CANADA	BRAND NEW BALLY/ STERNS 48 VOLT FLIPPER RELAY FOUND ON SOLENOID DRIVER BOARDS IN ALL GAMES AND ON SOLENOID EXPANDERS IN SOME GAMES $15.00 INCLUDES SHIPPING USA/ CANADA
	a The ¡°Slot Shot¡± is the most repetitious in a TZ game. It¡¯s the first shot on every ball and dozens of additional shots as the ball ends up in the ¡°Slot Machine¡± from every corner of the game. As game play continued the ball would start flying out of the ¡®Slot Scoop¡¯ hitting the flipper on the tip or on the heel or maybe not at all. Adjusting the Kicker Bracket by slightly bending it in or out a little causes a surprising difference in ball trajectory out of the scoop. After many ¡®adjustments¡¯ a setting would cause consistent ball travel resulting in hitting the Flipper¡¯s ¡°sweet spot¡± 7 times out of ten. After a few games the bracket would move back and the Scoop Shot would wander again.. This brace allowed for some stable adjustments of the bracket. ¡®Slot Shot Plotter¡¯ $29.00 including shipping.		BALLY BOLT BLOCKS -$4.00 EACH INCLUDING HARDWARE. ULTIMATE FLIPPER REPAIR ON PLATFORMS WITH TORN THREADS. DRILL OUT 8/32 THREADED HOLES TO 3/16". SLIDE BOLT BAR UNDER PLATFORM AND THREAD IN THE SOCKET SCREWS AND TIGHTEN. SOLD IN PAIRS ONLY ($8.00 INCLUDES POSTAGE).
		CV BELL IS BACK!!	CHROME BELL REPLACES DECAL IN CIRCUS VOLTAIRE BACKBOX COMES WITH MOUNTING HARDWARE $20.00 INCLUDES SHIPPING USA/ CANADA