Code: Select all
Location: /hw/module/001c01/node
IP34 Board: barcode MYD069 part 030-1707-003 rev -L
Location: /hw/module/001c01/node/cpubus/0
IP34PIMM Board: barcode MKZ626 part 030-1730-001 rev -G
Location: /hw/module/001c01/Ibrick/xtalk/13
ASTODYV10 Board: barcode MXH355 part 030-1826-002 rev -A
Location: /hw/module/001c01/Ibrick/xtalk/14
IP34 Board: barcode MYD069 part 030-1707-003 rev -L
Location: /hw/module/001c01/Ibrick/xtalk/15
IP34 Board: barcode MYD069 part 030-1707-003 rev -L
1 600 MHZ IP35 Processor
CPU: MIPS R14000 Processor Chip Revision: 2.3
FPU: MIPS R14010 Floating Point Chip Revision: 2.3
CPU 0 at Module 001c01/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
Processor revision: 2.3. Scache: Size 4 MB Speed 300 Mhz Tap 0xa
Main memory size: 1024 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 001c01/Slot 0: 1024 MB (enabled)
Bank 0 contains 256 MB (Standard) DIMMS (enabled)
Bank 1 contains 256 MB (Standard) DIMMS (enabled)
Bank 2 contains 256 MB (Standard) DIMMS (enabled)
Bank 3 contains 256 MB (Standard) DIMMS (enabled)
Integral SCSI controller 0: Version QL12160, low voltage differential
Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL12160, single ended
CDROM: unit 1 on SCSI controller 1
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V10
Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4
PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
PCI Adapter ID (vendor 0x1045, device 0xc861) PCI slot 5
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c01/Slot n0: Revision 6.210
USB controller: type OHCI
/usr/gfx/gfxinfo -vv
Code: Select all
Graphics board 0 is "ODYSSEY" graphics.
Managed (":0.0") 1280x1024
BUZZ version B.2
PB&J version 1
32MB memory
Banks: 2, CAS latency: 3
Monitor 0 type: Unknown
(Could not contact X server; thus, no XSGIvc information available)
uname -aR
Code: Select all
IRIX64 Fuel 6.5 6.5.30m 07202013 IP35scsicontrol -i /dev/scsi/*
Code: Select all
/dev/scsi/sc0d1l0: Disk SGI ST318406LW 2006
ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports: 16bit synch linkedcmds cmdqueing
Device is ready
/dev/scsi/sc1d1l0: CD-ROM TOSHIBA DVD-ROM SD-M14011007
ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports: synch linkedcmds
Device is not ready
/sbin/diskpatch -v
Code: Select all
sc0d1l0: Disk SGI ST318406LW 2006 Serial: 3FE21ELG
l1cmd serial all
Code: Select all
Data Location Value
------------------------------ ------------ --------
Local System Serial Number EEPROM 08:00:69:10:62:A3
Local Brick Serial Number EEPROM MYD069
Reference Brick Serial Number NVRAM MYD069
EEPROM Product Name Serial Part Number Rev T/W
---------- -------------- ---------- -------------------- --- ------
NODE IP34 MYD069 030_1707_003 L 00
MAC MAC ADDRESS NA NA NA NA
PIMM IP34PIMM MKZ626 030_1730_001 G 00
XIO ASTODYV10 MXH355 030_1826_002 A 00
EEPROM JEDEC-SPD Info Part Number Rev Speed SGI
---------- ------------------------ ------------------ --- ------ --------
DIMM 0 CE000000000000000CFE7000 M3 46L3313DT2-CA0 2D 10.0 N/A
DIMM 2 CE000000000000000CFF7000 M3 46L3313DT2-CA0 2D 10.0 N/A
DIMM 1 CE000000000000000C5BAD02 M3 46L3313DT2-CA0 2D 10.0 N/A
DIMM 3 CE000000000000000C65AD02 M3 46L3313DT2-CA0 2D 10.0 N/A
l1cmd flash status
Code: Select all
Flash image A currently booted
Image Status Revision Built
----- ------------- ---------- -----
A user default 1.20.6 03/12/2003 11:01:29
B valid 1.20.6 03/12/2003 11:01:29
l1cmd env
Code: Select all
Environmental monitoring is enabled and running.
Description State Warning Limits Fault Limits Current
-------------- ---------- ----------------- ----------------- -------
12V Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 11.50
12V IO Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 11.81
5V Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.20
3.3V Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.30
2.5V Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.46
1.5V Enabled 10% 1.35/ 1.65 20% 1.20/ 1.80 1.47
5V aux Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.02
3.3V aux Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.27
PIMM0 12V bias Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 11.81
Fuel SRAM Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.54
Fuel CPU Enabled 10% 1.44/ 1.76 20% 1.28/ 1.92 1.59
PIMM0 1.5V Enabled 10% 1.35/ 1.65 20% 1.20/ 1.80 1.49
PIMM0 3.3V aux Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.29
PIMM0 5V aux Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.04
XIO 12V bias Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 11.44
XIO 5V Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.20
XIO 2.5V Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.46
XIO 3.3V aux Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.30
Description State Warning RPM Current RPM
-------------- ---------- ----------- -----------
FAN 0 EXHAUST Enabled 920 1228
FAN 1 HD Enabled 1560 2244
FAN 2 PCI Enabled 1120 1558
FAN 3 XIO 1 Enabled 1600 2274
FAN 4 XIO 2 Enabled 1600 2130
FAN 5 PS Enabled 1600 1781
Advisory Critical Fault Current
Description State Temp Temp Temp Temp
-------------- ---------- --------- --------- --------- ---------
NODE 0 Enabled 60C/140F 65C/149F 70C/158F 33C/ 91F
NODE 1 Enabled 60C/140F 65C/149F 70C/158F 31C/ 87F
NODE 2 Enabled 60C/140F 65C/149F 70C/158F 23C/ 73F
PIMM Enabled 60C/140F 65C/149F 70C/158F 40C/104F
ODYSSEY Enabled 60C/140F 65C/149F 70C/158F 29C/ 84F
BEDROCK Enabled 70C/158F 75C/167F 80C/176F 34C/ 93F
]