O2, R12K 400Mhz, 1GB RAM, 32GB HDD

[kubatyszko]

hinv -vm

Code: Select all

CPU: MIPS R12000 Processor Chip Revision: 3.5
FPU: MIPS R12010 Floating Point Chip Revision: 0.0
1 400 MHZ IP32 Processor
Main memory size: 1024 Mbytes
Secondary unified instruction/data cache size: 2 Mbytes on Processor 0
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
FLASH PROM version 4.18
Integral SCSI controller 0: Version ADAPTEC 7880
  Disk drive: unit 2 on SCSI controller 0 (unit 2)
  CDROM: unit 4 on SCSI controller 0
Integral SCSI controller 1: Version ADAPTEC 7880
On-board serial ports: tty1
On-board serial ports: tty2
On-board EPP/ECP parallel port
CRM graphics installed
Integral Ethernet: ec0, version 1
Iris Audio Processor: version A3 revision 0
  PCI Adapter ID (vendor 0x9004, device 0x8078) PCI slot 1
  PCI Adapter ID (vendor 0x9004, device 0x8078) PCI slot 2
Video: MVP unit 0 version 1.4
AV: AV1 Card version 1, Camera not connected.
Vice: TRE



/usr/gfx/gfxinfo -vv

Code: Select all

Graphics board 0 is "CRM" graphics.
        Managed (":0.0") 1280x1024
        32 bitplanes
        board revision 2, CRM revision C, GBE revision B
         Monitor 0 type: Unknown
        (Could not contact X server; thus, no XSGIvc information available)



uname -aR

Code: Select all

IRIX no2 6.5 6.5.22m 10070056 IP32


scsicontrol -i /dev/scsi/*

Code: Select all

/dev/scsi/sc0d2l0:  Disk          SGI     ST336607LC      2743
ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing
Device is  ready
/dev/scsi/sc0d4l0:  CD-ROM        TOSHIBA CD-ROM XM-6401TA1003
ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports:  reladdr synch linkedcmds
Device is  not ready



/sbin/diskpatch -v

Code: Select all

sc0d2l0:  Disk         SGI     ST336607LC      2743  Serial: 3JA9Z2MW


[ShadeOfBlue]

Nicely maxed out O2

I am curious about the temperature of the HDD, could you please post the output of scsimon after the system has been running for about an hour?

[kubatyszko]

Code: Select all

no2 26# ./scsimon /dev/scsi/sc0d2l0
Inquiry response:       [SGI     ST336607LC      2743]
Current temperature:    26C/78F
Maximum temperature:    68C/154F
Drive uptime (total):   29117 minutes (= 20d 5h 17m)
Next internal test in:  112 minutes
Self-test data (newest first):
         0: at: 1h      type: bg short          result: completed OK
         1: at: 1h      type: bg short          result: completed OK
no2 27# !!
./scsimon /dev/scsi/sc0d2l0
Inquiry response:       [SGI     ST336607LC      2743]
Current temperature:    31C/87F
Maximum temperature:    68C/154F
Drive uptime (total):   29133 minutes (= 20d 5h 33m)
Next internal test in:  96 minutes
Self-test data (newest first):
         0: at: 1h      type: bg short          result: completed OK
         1: at: 1h      type: bg short          result: completed OK
no2 28#
no2 28# !!
./scsimon /dev/scsi/sc0d2l0
Inquiry response:       [SGI     ST336607LC      2743]
Current temperature:    35C/95F
Maximum temperature:    68C/154F
Drive uptime (total):   29159 minutes (= 20d 5h 59m)
Next internal test in:  70 minutes
Self-test data (newest first):
         0: at: 1h      type: bg short          result: completed OK
         1: at: 1h      type: bg short          result: completed OK
no2 29# date
Fri Nov  2 11:59:18 JST 2012
no2 30# !./s
./scsimon /dev/scsi/sc0d2l0
Inquiry response:       [SGI     ST336607LC      2743]
Current temperature:    35C/95F
Maximum temperature:    68C/154F
Drive uptime (total):   29179 minutes (= 20d 6h 19m)
Next internal test in:  50 minutes
Self-test data (newest first):
         0: at: 1h      type: bg short          result: completed OK
         1: at: 1h      type: bg short          result: completed OK
no2 31#



After approx 1 hour, temp gradually went up from 26C to 35C.
I'm keeping the machine loaded, but without significant disk IO

Some 1 hour later, the temp went up to 38C

Code: Select all

bash-4.0# ./scsimon /dev/scsi/sc0d2l0
Inquiry response:       [SGI     ST336607LC      2743]
Current temperature:    36C/96F
Maximum temperature:    68C/154F
Drive uptime (total):   29206 minutes (= 20d 6h 46m)
Next internal test in:  22 minutes
Self-test data (newest first):
         0: at: 1h      type: bg short          result: completed OK
         1: at: 1h      type: bg short          result: completed OK
bash-4.0# !!
./scsimon /dev/scsi/sc0d2l0
Inquiry response:       [SGI     ST336607LC      2743]
Current temperature:    38C/100F
Maximum temperature:    68C/154F
Drive uptime (total):   29236 minutes (= 20d 7h 16m)
Next internal test in:  112 minutes
Self-test data (newest first):
         0: at: 1h      type: bg short          result: completed OK
         1: at: 1h      type: bg short          result: completed OK


And not long later, temperature seems to have stabilized at 37C.

Code: Select all

bash-4.0# !./s
./scsimon /dev/scsi/sc0d2l0
Inquiry response:       [SGI     ST336607LC      2743]
Current temperature:    37C/98F
Maximum temperature:    68C/154F
Drive uptime (total):   29249 minutes (= 20d 7h 29m)
Next internal test in:  100 minutes
Self-test data (newest first):
         0: at: 1h      type: bg short          result: completed OK
         1: at: 1h      type: bg short          result: completed OK
bash-4.0#


Ambient temperature in my room is some 20-22C.

[ShadeOfBlue]

Thanks

[[[C|-|E]]]

do you have pics ?