UPDATE September 2011: replaced 73GB with two 146GB HDDs
UPDATE January 2012: RAM upgrade, soundcard
PCI cards are LSI 20320-HP, Creative SB0090 soundcard and Belkin F5U220 USB.
UPDATE September 2012: Belkin F5U503 Firewire card and 1TB external disk
LSI 21320 to replace LSI 20320-HP (for more usefully positioned sockets)
UPDATE May 2013: replaced V10 (030-1826-003 rev -A) with V12 (ex-Tezro)
UPDATE March 2014: tried Adaptec Duoconnect AUA-3020 without success-
UPDATE March 2014: replaced USB card with narrow SCSI socket cabled to Channel B on the LSI 21320, to drive a slide scanner (Nikon Coolscan II, seems fine with xsane from nekoware)
Hinv etc from May 2013 after fitting the V12:
hinv -vm
Code: Select all
Location: /hw/module/001c01/node
IP34 Board: barcode NAS621 part 030-1707-003 rev -M
Location: /hw/module/001c01/node/cpubus/0
IP34PIMM Board: barcode MSY420 part 030-1891-001 rev -D
Location: /hw/module/001c01/Ibrick/xtalk/13
ODY128B1_2 Board: barcode NWM092 part 030-1884-005 rev -B
Location: /hw/module/001c01/Ibrick/xtalk/14
IP34 Board: barcode NAS621 part 030-1707-003 rev -M
Location: /hw/module/001c01/Ibrick/xtalk/15
IP34 Board: barcode NAS621 part 030-1707-003 rev -M
1 700 MHZ IP35 Processor
CPU: MIPS R16000 Processor Chip Revision: 2.1
FPU: MIPS R16010 Floating Point Chip Revision: 2.1
CPU 0 at Module 001c01/Slot 0/Slice A: 700 Mhz MIPS R16000 Processor Chip (enabled)
Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz Tap 0xa
Main memory size: 4096 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 001c01/Slot 0: 4096 MB (enabled)
Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
Integral SCSI controller 6: Version IEEE1394 SBP2
Integral SCSI controller 7: Version LS1030, low voltage differential
Integral SCSI controller 8: Version LS1030, low voltage differential
Integral SCSI controller 0: Version QL12160, low voltage differential
Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL12160, single ended
CDROM: unit 4 on SCSI controller 1
Disk drive / removable media: unit 6 on SCSI controller 1
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V12
Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4
Iris Audio Processor: version EMU revision A3, number 1
PCI Adapter ID (vendor 0x1033, device 0x0035) PCI slot 1
PCI Adapter ID (vendor 0x1033, device 0x0035) PCI slot 1
PCI Adapter ID (vendor 0x1033, device 0x00e0) PCI slot 1
PCI Adapter ID (vendor 0x1000, device 0x0030) PCI slot 2
PCI Adapter ID (vendor 0x1000, device 0x0030) PCI slot 2
PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
PCI Adapter ID (vendor 0x1102, device 0x0004) PCI slot 2
PCI Adapter ID (vendor 0x1102, device 0x7003) PCI slot 2
PCI Adapter ID (vendor 0x1102, device 0x4001) PCI slot 2
PCI Adapter ID (vendor 0x104c, device 0x8024) PCI slot 3
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
PCI Adapter ID (vendor 0x1045, device 0xc861) PCI slot 5
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c01/Slot n0: Revision 6.210
DMediaPro DM10 FW option: unit 0, revision 1.1.0
USB controller: type OHCI
USB controller: type OHCI
USB controller: type OHCI
gfxinfo
Code: Select all
Graphics board 0 is "ODYSSEY" graphics.
Managed (":0.0") 1920x1200
BUZZ version B.2
PB&J version 1
128MB memory
Banks: 4, CAS latency: 3
Monitor 0 type: GSM 8704
Channel 0:
Origin = (0,0)
Video Output: 1920 pixels, 1200 lines, 60.00Hz (1920x1200_60p.vfo)
The "GSM8704" is in this case a TV - 22LG3000 - connected using DVI-HDMI; my Pi uses the other HDMI input and there is also a VGA input for the Indigo2, RiscPC and EspressoPC. This replaced an Iiyama 9017 CRT when we got a new TV!
uname -aR reports "IRIX64 redbox 6.5 6.5.30m 07202013 IP35"
scsicontrol -v
Code: Select all
/dev/scsi/sc0d1l0: Disk FUJITSU MAP3147NP 5605
ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports: 16bit synch linkedcmds cmdqueing
Device is ready
/dev/scsi/sc1d4l0: CD-ROM TOSHIBA DVD-ROM SD-M14011007
ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports: synch linkedcmds
Device is not ready
/dev/scsi/sc1d6l0: Disk SyQuest SQ3270S 3_05
ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports: synch linkedcmds
Device is not readyThe Syquest shows "Device is not ready" as there is no cartridge present - it seems to operate very nicely, mounting automatically when a cartridge is inserted and unmounting from the "Eject" option on the menu.
I also have a second 146GB drive fitted but only connect power when wanting to back up. The Fujitsu is set to spin up on command rather than power-on, so PROM-only operations can happen without wear on the drive (handy when fitting / troubleshooting other hardware!).
L1 info - for some reason I cannot get anything from "l1cmd pci" although I am sure this has worked in the past.
l1cmd flash status
Code: Select all
Flash image A currently booted
Image Status Revision Built
----- ------------- ---------- -----
A user default 1.44.0 07/17/2006 18:20:38
B valid 1.44.0 07/17/2006 18:20:38l1cmd serial all
Code: Select all
Data Location Value
------------------------------ ------------ --------
Local System Serial Number EEPROM 08:00:69:10:6F:CB
Local Brick Serial Number EEPROM NAS621
Reference Brick Serial Number NVRAM NAS621
EEPROM Product Name Serial Part Number Rev T/W
---------- -------------- ------------- -------------------- --- ------
NODE IP34 NAS621 030_1707_003 M 00
MAC MAC ADDRESS NA NA NA NA
PIMM IP34PIMM MSY420 030_1891_001 D 00
XIO ODY128B1_2 NWM092 030_1884_005 B 00
EEPROM JEDEC-SPD Info Part Number Rev Speed SGI
---------- ------------------------ ------------------ ---- ------ --------
DIMM 0 CE000000000000000C9B0F00 M3 46L2820DT2-CA0 2D 10.0 N/A
DIMM 2 CE0000000000000028181900 M3 46L2820BT1-CA0 0B 8.0 N/A
DIMM 1 CE000000000000000C5F0B00 M3 46L2820DT2-CA0 2D 10.0 N/A
DIMM 3 CE0000000000000027CE1400 M3 46L2820BT1-CA0 0B 8.0 N/A l1cmd env
Code: Select all
Environmental monitoring is enabled and running.
Description State Warning Limits Fault Limits Current
-------------- ---------- ----------------- ----------------- -------
12V Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.063
12V IO Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.125
5V Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.096
3.3V Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.337
2.5V Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.470
1.5V Enabled 10% 1.35/ 1.65 20% 1.20/ 1.80 1.466
5V AUX Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.122
3.3V AUX Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.285
PIMM 12V BIAS Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.125
SRAM Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.522
VCPU Enabled 10% 1.13/ 1.38 20% 1.00/ 1.50 1.241
PIMM 1.5V Enabled 10% 1.35/ 1.65 20% 1.20/ 1.80 1.495
PIMM 3.3V AUX Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.285
PIMM 5V AUX Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.122
XIO 12V BIAS Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 11.938
XIO 5V Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.070
XIO 2.5V Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.457
XIO 3.3V AUX Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.285
Description State Warning RPM Current RPM
--------------- ---------- ----------- -----------
FAN 0 EXHAUST Enabled 920 1188
FAN 1 HD Enabled 1560 2280
FAN 2 PCI Enabled 1120 1562
FAN 3 XIO 1 Enabled 1600 2463
FAN 4 XIO 2 Enabled 1600 2376
FAN 5 PS Enabled 1349 3308
Advisory Critical Fault Current
Description State Temp Temp Temp Temp
----------------- ---------- --------- --------- --------- ---------
0 NODE 0 Enabled [Autofan Control] 80C/176F 35C/ 95F
1 NODE 1 Enabled [Autofan Control] 80C/176F 39C/102F
2 NODE 2 Enabled [Autofan Control] 80C/176F 28C/ 82F
3 PIMM Enabled [Autofan Control] 80C/176F 41C/105F
4 ODYSSEY Enabled [Autofan Control] 80C/176F 44C/111F
5 BEDROCK Enabled [Autofan Control] 85C/185F 39C/102F
The V10 used to run at 38C, so 44C after an hour's use (and the PIMM at 2C wamer) was a very slight concern, but the fans seem only slightly faster. It was January 2012 when I last put env output in this entry, quite possibly at night so the ambient temperature may have been several degrees lower (the Fuel is in a north-facing corner room). Checking again later, the V12 and PIMM were both down a couple of degrees AND the fans were slower, so I should stop worrying!